Remote control Remo 8
2
Remote control Remo 8
software version 1.5 and up • Version 18.10.2016 • The right to make technical changes is reserved. Errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de
2.3.5. WL400 / WL800 / WL-Z ventilation units
To teach/delete the wireless connection, the fan cover
need not be
removed
.
Configuration:
Deletion:
2.3.6. Modules RF-MSG, RF-Relay, RF-L
The configuration and deletion should only be perfor-
med by a trained electrician!
Configuration:
Deletion:
3. Operating devices/motors using the
transmitter
3.0.1. Devices, light, motors and ventilation units
WFL / WL305 / WL610
Sequence of ventilation steps for roof-top fan WL305/610:
Exhaust air8 - 7 - 6 - 5 - 4 - 3 - 1 - Off - Recirculation air 1 - 2 - 3 - 4 - 5
- 6 - 7 - 8
3.0.2. Ventilation Units WL400 / WL800
You
tap on the arrow keys
to adjust the speed of the fan in 10% in-
crements (10 fan speeds altogether).
Holding down the arrow keys
changes the speed continuously. If you
release the key, the speed stops changing.
Note:
Radio interference (rarely) may cause the speed to continue chan-
ging after the key is released. In this case, tap the key again to stop it.
Each time the
OFF
state is reached, the speed variation stops auto-
matically, so that a direct change between extraction and circulation
modes is impossible.
4. Care and maintenance
Clean the hand-held transmitter with a damp cloth. Do not use detergent.
4.1. Troubleshooting
Device/drive does not react to button press:
4.2. Replace the battery
Dispose of the used battery properly - empty batteries should not be
thrown away in household refuse.
1.
Bring the hand-held transmitter into the set-up
readiness state by pressing and holding the centre of
the +/- button on the hand-held transmitter until an "L"
for Learn and a number (channel) are displayed.
2.
Using + or - change to the hand-held transmitter
channel that you want to program (L 1 to L 8).
3.
Switch on the power supply to the fan or switch the
power supply off briefly if the unit is already powered.
4.
The fan will send a "Teach" telegram every 10 seconds
for 5 minutes after connecting the power. This teaches
the hand-held transmitter automatically.
Once the "L" in the display has gone out, you can
control the device with this hand-held transmitter
channel.
1.
Bring the held-held transmitter into the deletion
readiness state. To do this, press and hold the middle
of the +/- button until an "L" appears in the display.
Then press again until a "C" for Clear appears in the
display.
2.
Using + or - change to the hand-held transmitter
channel that you want to delete (C 1 to C 8).
3.
Switch off the power supply to the fan briefly (switch the fuse
on/off). This teaches the hand-held transmitter automatically.
Once the "C" in the display has gone out, you can control the
device with this hand-held transmitter channel.
1.
Bring the hand-held transmitter into the set-up
readiness state by pressing the centre of the +/- button
on the hand-held transmitter until an "L" for Learn and
a number (channel) are displayed.
2.
Using + or - change to the hand-held transmitter
channel that you want to program (L 1 to L 8).
3.
Now activate the voltage supply of RF-MSG or RF-Relay-UP. The
device automatically configures a connection 3 seconds after the
mains voltage is applied. The "L" in the display goes out.
1.
Bring the held-held transmitter into the deletion
readiness state. For this purpose press the +/- button in
the centre till "L" appears in the display. Then press
again till a "C" for Clear appears in the display.
2.
Using + or - change to the hand-held transmitter
channel that you want to delete (C 1 to C 8).
3.
Now activate the RF-MSG voltage supply. The motor control unit
will be cleared automatically 3 seconds after the mains voltage
is applied. The "C" in the display goes out.
1.
Select the hand-held transmitter channel that you want
using the + and - buttons.
2.
You can now operate the assigned device and/or drive
using the Up, Down and Stop buttons.
Switching
devices
Dimming
light
Elsner
roof-top
fans
Moving
drives
1
.
On/Off
Short:
On (last dim
value)
Long:
Brighter
1 step up
Up
Short:
Incremental
operation
Long:
Normal drive
(up to end
position)
2
.
Off
Off
Off/closed
Stop
On/Off
Short:
Off
Long:
darker
1 step down
Down
Short:
Incremental
operation
Long:
Normal drive
(up to end
position)
Fan OFF
(stopped,
flap closed)
Circulation mode
Press
Increase speed
Decrease speed
(until OFF)
Fan OFF
Press
Extraction mode
Decrease speed
(until OFF)
Increase speed
Fan OFF
Cause
Procedure
Wireless contact interrupted,
transmitter too far from receiver
Choose another location
Battery drained
Replace the battery
No voltage to or faulty receiver
unit
Switch on receiver unit (e.g.
control unit). Should wireless
contact still not be established,
please contact Customer Service
Remote control is blocked, as one
of the keys was stuck or was held
down for more than 10 seconds
(battery protection)
Press first the Up key and then
the Down key to unlock the
remote control
1.
Open the housing panel on the rear of the hand-held transmitter
(using a cross-head screwdriver).
2.
Lift the used battery carefully out
of the holder. Be careful of the
clips when inserting the new
battery.
CR2032 type battery, 3 V.
3.
Screw the rear housing panel closed again.
