Remote control Remo 8
1
Remote control Remo 8
software version 1.5 and up • Version 18.10.2016 • The right to make technical changes is reserved. Errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de
Remote Control Remo 8
1. Description
The
Remote control Remo 8
offers an Up/Down/Stop or
On/Off control for eight channels and can be set up with
various devices. If the remote control is not being used, it
is safely placed in the included magnetic wall-holder.
Remo 8 is suitable for the following devices:
• WS1/WS1000 Color and WS1/WS1000 Style control
(version 1.1 and up)
• Solexa control (v. 3.6 and up), Arexa (v. 3.7 and up)
• Solexa II
• WL305, WL610 ventilators (version 4.0 and up), WFL
air supply (version 2.0 and up), WL400/800, WL-Z
• RF-Relay (version 2.0 and up), RF-MSG motor control
unit, RF-VM ventilation module, RF-L dimmer
• XS MSG2-AP wireless motor control unit (v.2.0)
• Lixa control unit
• KNX Touch One (Style) touch panel
The software version of the device must be appropriate for interaction
with the remote control!
Moisture is harmful to the electronic components of
the hand-held transmitter. You must therefore:
• Not leave it in the rain
• Not leave it outside overnight
• Protect it from frost
1.1. Scope of delivery
• Hand-held transmitter with battery
• Wall-mounted holder with screw covers
1.2. Technical data
The product conforms with the provisions of EU directives.
2. Installation and commissioning
2.1. Installing the wall-mounted holder
2.2. Notes on wireless equipment
When planning facilities with devices that communicate via radio, ade-
quate radio reception must be guaranteed. The range of wireless control
will be limited by legal regulation and structural circumstances. Avoid
sources of interference and obstacles between receiver and transmitter,
that could disturb the wireless communication. Those would be for ex-
ample:
• Walls and ceilings (especially concrete and solar protection
glazing).
• Metal surfaces next to the wireless participants (e. g. aluminium
construction of a conservatory).
• Other wireless devices and powerful local transmitters (e.g.
wireless headphones), which transmit on the same frequency (868,2
MHz). Please maintain a minimum distance of 30 cm between
wireless transmitters for that reason.
2.3. Configuring and deleting a connection
Each of the hand-held transmitter's eight channels can control one or
more radio channels (units).
2.3.1. WS1/WS1000 Color/Style control systems
Configuration:
Deletion:
2.3.2. Solexa II control unit
Configuration:
Deletion:
2.3.3. XS MSG2-AP motor control unit
Configuring and deleting should only be performed by
a trained electrician!
Configuration:
Deletion:
2.3.4. Solexa / Arexa control units, WL305 / WL610
/ WFL ventilation units, RF-VM
The configuration and deletion should only be perfor-
med by a trained electrician!
Configuration:
Deletion:
Housing
Plastic
Colours
• white/light grey
• aluminium/graphite (partially painted)
Installation
with magnetic wall-holder
Protection category
IP 40
Dimensions
Transmitter approx. 41 x 140 x 21 (WxHxD,
mm), Holder approx. 54 x 150 x 11 (WxHxD,
mm)
Total weight
approx. 95 g
Ambient temperature
Operating 0…50 °C, storage -10…+60 °C
Ambient humidity
max. 95% rH, avoid condensation
Operating voltage
3 V CR2032 type battery
Radio frequency
868.2 MHz
Channels
8
The holder must be firmly screwed to the wall.
Please use suitable dowels and screws as
supports. The screws should then be covered
with the provided screw covers.
The hand-held transmitter is held in position in
its tray with magnets.
1.
Bring the control unit into the set-up readiness state: Menu
System > Installation > Wireless connection > Setup
.
Please also follow the instructions in the manual.
2.
Press the centre of the +/- button on the hand-held
transmitter until an "L" for Learn and a number
(channel) are displayed.
The channel selected will not affect the configuration of
the WS1/WS1000.
3.
Press the Up arrow button to establish the wireless
connection with the control system.
4.
The "L" in the display goes out. The remote control is now
configured for the control system.
The
System > Installation > Wireless connection > Status
menu
item allows you to give the hand-held transmitter a separate
name and assign individual drives and devices to the hand-held
transmitter channels.
1.
Delete the hand-held transmitter on the control system menu:
Menu
System > Installation > Wireless connection > Delete
.
Please also follow the instructions in the manual.
1.
Bring the control unit into the set-up readiness state: Menu
Base
Settings > LEA
. Please also follow the instructions in the manual.
2.
Press the centre of the +/- button on the hand-held
transmitter until an "L" for Learn and a number
(channel) are displayed.
The channel selected will not affect the configuration of
the WS1/WS1000.
3.
Press the Up arrow button to establish the wireless
connection with the control system.
4.
The "L" in the display goes out. The remote control is now
configured for the control system. The assignment of an output
to a hand-held transmitter channel is made at the basic setting of
the respective output. Menu:
Base Settings > OUt > SP X > INPt
1.
Delete the hand-held transmitter on the control system menu:
Menu
Base Settings > StAt
. Please also follow the instructions in
the manual.
1.
Bring the desired channel of the motor control unit into the set-
up readiness state (see manual chapter "Motor control unit
wireless connection
- Remo 8").
2.
Bring the hand-held transmitter into the set-up
readiness state by pressing the centre of the +/- button
on the hand-held transmitter until an "L" for Learn and
a number (channel) are displayed.
3.
Using + or - change the hand-held transmitter channel
that you would like to connect to the motor control unit
channel (L 1 to L8).
4.
Press the Up arrow button to establish the wireless
connection with the motor control unit. The "L" in the
display goes out. The hand-held transmitter channel is
now configured to the channel of the motor control
unit.
1.
Bring the desired channel of the motor control unit into the set-
up readiness state (see manual chapter "Motor control unit
wireless connection - Remo 8").
2.
Bring the held-held transmitter into the deletion
readiness state. For this purpose press the +/- button in
the centre till "L" appears in the display. Then press
again till a "C" for Clear appears in the display.
3.
Using + or - change to the hand-held transmitter that
you want to delete (C 1 to C 8).
4.
Press the Up arrow button to delete the wireless
connection to the motor control unit channel. The "C"
in the display goes out.
1.
Bring the hand-held transmitter into the set-up
readiness state by pressing the centre of the +/- button
on the hand-held transmitter until an "L" for Learn and
a number (channel) are displayed.
2.
Using + or - change to the hand-held transmitter that
you want to program (L 1 to L 8).
3.
Press the programmer button inside the device using an
insulated screwdriver. The "L" in the display goes out. Now you
can control the device with this hand-held transmitter channel.
1.
Bring the held-held transmitter into the deletion
readiness state. For this purpose press the +/- button in
the centre till "L" appears in the display. Then press
again till a "C" for Clear appears in the display
2.
Using + or - change to the hand-held transmitter
channel that you want to delete (C 1 to C 8).
3.
Now press the programmer button inside the device using an
insulated screwdriver. The wireless connection is deleted. The
"C" in the display goes out.