elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя | Manualshive

Страница: 29 / 68

background image

27

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

Block

If necessary, activate the switching output block and set what a 1 or 0 at the block entry
means and what happens in the event of a block.

The behaviour of the switching output on release is dependent on the value of the pa-
rameter "Switching output sends" (see "Switching output")

6.5.

Light control

For light control, the sensor detects the brightness in the room. Activate the light con-
trol.

Set, in which cases the

data

received via object for setpoint value, setpoint value-ac-

tual difference, dimming increment and times are to be retained. Please note that the
setting "After power supply restoration and programming" should not be used for the
initial start-up, as the factory settings are always used until the first communication.

Use switching output block

No • Yes

Analysis of the blocking object

• At value 1: block | At value 0: release
• At value 0: block | At value 1: release

Blocking object value before first call

0 • 1

Action when locking

• Do not send message
• send 0
• send 1

Action upon release
(with 2 seconds release delay)

[Dependent on the "Switching output
sends" setting]

Switching output sends on change

do not send message •
Status object/s send/s

Switching output sends on change to 1

do not send message •
If switching output = 1



send 1

Switching output sends on change to 0

do not send message •

If switching output = 0



send 0

Switching output sends on change and
periodically

Send switching output status

Switching output sends on change to 1 and
periodically

If switching output = 1



send 1

Switching output sends on change to 0 and
periodically

If switching output = 0



send 0

Use control

No • Yes

Maintain the

data received via object for setpoint, set-
point-actual difference, dimming increment
and times

• never
• after power supply restoration
• after power supply restoration and
programming

«
...
27
28
29
30
31
...
»

Содержание Mini-Sewi KNX L-Pr





































































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренд: Omega Страницы: 2

Бренд: D-tect Systems Страницы: 4

Бренд: QOLSYS Страницы: 3

Бренд: ADEMCO Страницы: 56

Бренд: Takex Страницы: 8

Бренд: SAFE-T-ALERT Страницы: 5

Бренд: Brickcom Страницы: 7

Бренд: G-Force Страницы: 2

DS-2DF8C425MHS-DEL

Бренд: HIKVISION Страницы: 117

Бренд: DMP Electronics Страницы: 2

Pursuit PRO-9649N

Бренд: Audiovox Страницы: 8

Бренд: BUCKINGHAM MFG Страницы: 2

RoboSHOT HDBT Series

Бренд: VADDIO Страницы: 111

Бренд: THORLABS Страницы: 16

Бренд: AVGO Страницы: 18

Бренд: Moog Videolarm Страницы: 2

Бренд: Gemini Страницы: 16

1080P High Performance Forward Facing Camera

Бренд: RoadHawk Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды