elsner elektronik KNX PY Скачать руководство пользователя страница 17

Страница: 17 / 22

Setting of parameters

Pyranometer KNX PY

• Status: 22.07.2019 • Technical changes reserved. Errors reserved.

Block

Only if switching output block is used:

Blocking

„Blocking“ only appears if using „Switching output sends on change“

If block of the switching output is used:

6.3.

Logic

Switching delay from 1 to 0

none • 1 secs … 2 h

Switching output transmits

• on change
• on change to 1
• on change to 0
• on change and periodically
• on change to 1 and periodically
• on change to 0 and periodically

Transmit switching output in the cycle of

(only if sending “periodically“)

5 secs … 2 h

Use switching output block

No • Yes

Use switching output block

Yes

Evaluation of blocking object

• on value 1: block | on value 0: release
• on value 0: block | on value 1: release

Value of blocking object
before 1. communication

0 • 1

Behaviour of switching output on block

• do not transmit message
• transmit 0
• transmit 1

Behaviour of switching output on release

if switching output = 0



transmit 0

Use block of the switching output

Yes • No

Use block of the switching output

Yes

Evaluation of the blocking object

• if value 1: block | if value 0: release
• if value 0: block | if value 1: release

Value of the blocking object before
1. communication

0 • 1

Behaviour of the switching output
with blocking

• do not send telegram
• send 0
• send 1

Behaviour of the switching output
with release (selection possible according
to previous settings)

• do not send telegram
• send status of the switching output
• if switching output = 1 => send 1
• if switching output = 0 => send 0

Communication objects logic inputs

do not release • release

Содержание KNX PY























Результаты поиска

Содержание KNX PY

Отзывы:

Похожие инструкции для KNX PY

Бренды по названию

Популярные бренды

elsner elektronik KNX PY, Технические характеристики и инструкции по установке

Результаты поиска

Содержание KNX PY

Отзывы:

Похожие инструкции для KNX PY

Бренды по названию

Популярные бренды