5.0 LOCAL CONTROL
5.1 Input selection
The input to be converted to high resolution is selected pressing one of the five INPUT
SELECT keys. The led ON indicates which input is selected at that moment.
5.2 Resolution of the output signal
The resolution of the output signal can be set pressing the RESOLUTION / SELECT button
repeatedly. The resolution active is indicated by the led ON and remains saved after
subsequent power-on.
WARNING
Selecting PC1 - PC2, the format in output
remains that of the PC input signal.
5.3 Presets from keypad
a) Setting of the input at power-on
To enable a particular input at power-on of the unit, hold down the button of that input for 3
seconds.
A flash of the built-on led indicates saving of the command. From this moment on, the
MDL200 will enable that input at power-on.
The factory setting enables the PC1 input.
b) IR
reception
IR reception can be disabled maintaining pressed the RESOLUTION / SELECT button
during the power-on. IR reception can be re-enabled repeating the routine as above the
default unit enables IR reception.
6.0 FUNCTIONS WITH IR REMOTE CONTROL
The unit is equipped with a receiver for an IR remote control which must be purchased
separately.
WARNING
The remote control is of the self-teaching type. After inserting the batteries
and each time these are changed, press the "Set" key
for a few moments followed by the button with violet border
The following functions, divided into seven active groups, are performed with the IR remote
control:
1st Group – 1 key: Self-teaching:
Set + key CV1
Self-teaching of the remote control each
time the batteries are changed.
2nd Group - 2 keys: Save and recall
Save
Saves all the current presets.
Recall
Recalls the presets saved previously
with SAVE.
3rd Group - 1 key: Default
DEFAULT
Restores all the standard conditions
of the unit.
4th Group - 11 keys:
INPUT SELECT
Press the key of the input to be converted to high resolution.
The input selected is identified by switching on of the built-in led
of the button located on the console.
ATTENTION: ONLY TIME FIRST 5 KEYS ARE ACTIVE
5th Group - 4 keys: On Screen Display
Use the 4 keys
+
,
-
,
PICT
and
MODE
to use OSD.
6th Group - 1 key: Resolution
RESOLUTION
Sets the format of the high resolution output
signal. The format set
can be viewed by checking the leds on the console of the MDL200 unit.
7th Group - 2 keys: VOLUME OUT
THIS FUNCTION IS NOT AVAILABLE
8th Group - 2 keys: MICrophone
THIS FUNCTION IS NOT AVAILABLE
9th Group - 10 keys: AUX DRY CONTACTS THIS FUNCTION IS NOT AVAILABLE
10th Group - 2 keys: MUTE ON-OFF
THIS FUNCTION IS NOT AVAILABLE
Puss MUTE ON to reset the audio level
Puss MUTE OFF to restore the audio level
7.0 COMPUTER CONTROL via RS232
On its site
www.elprovideolabs.com
, Elpro has made available software running under
Windows suitable for controlling the MDL200 via RS232.
If the user intends to develop personalized software, the protocols to be implemented RS232
is available on the same site.
All functions of the MDL200 can be controlled through transmission/reception by a computer
of strings of hexadecimal and ASCII characters.
The procedure for data exchange via RS232 is as follows:
Transmission standard:
8 data bits, no parity, 1 stop bit and speed of 9600 baud.
MDL200
SWITCHER/HIGH RESOLUTION SCALER
MDL200
SWITCHER/HIGH RESOLUTION SCALER
ELPRO Video Labs s.r.l.
Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY
Tel.+39 0119348778 - FAX +39 0119348779
ELPRO Video Labs s.r.l.
Via della Praia 4/a FERRIERA di BUTTIGLIERA ALTA (TO) – ITALY
Tel.+39 0119348778 - FAX +39 0119348779
8 9