background image

Q N W 4 0 0 0

I N S T R U C T I O N   M A N U A L

The exclamation point within an equilateral 
triangle is intended to alert the user to the 
presence of important operating and maintenance
 (servicing) instructions in the literature 
accompanying the appliance.

CAUTION

CAUTION :  TO REDUCE THE RISK OF ELECTRIC SHOCK.
     DO NOT REMOVE COVER (OR BACK).
     NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK 

DO NOT OPEN

The lightning flash with arrowhead symbol, within 
an equilateral triangle, is intended to alert the user 
to the presence of uninsulated "dangerous 
voltage" within the product's enclosure that may 
be of sufficient magnitude to constitute a risk of 
electric shock to persons.

CAUTION

.

Do not use any power supply other than

specified.

WARNING

TO REDUCE THE RISK OF FIRE OR

ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE.

* The CAUTION label is attached on the

bottom of camera.

INFORMATION

This equipment has been tested and found

to comply with the limits for Class A digital

device,  pursuant  to  Part  15  of  the  FCC

Rules.  These  limits  are  designed  to

provide  reasonable  protection  against

harmful  interference  when  the  equipment

is  operated  in  a  commercial  environment.

This  equipment  generates,  use,  and  can

radiate  radio  frequency  energy  and,  if  not

installed  and  used  in  accordance  with  the

instruction  manual,  may  cause  harmful

interference  to  radio  communications.

Operation  of  this  equipment  in  a

residential  area  is  likely  to  cause  harmful

interference in which case the user will be

required  to  correct  the  interference  at  his

own expense.

USER-INSTALLER  CAUTION:

Your

authority  to  operate  this  FCC  verified

equipment  could  be  voided  if  you  make

changes  or  modifications  not  expressly

approved  by  the  party  responsible  for

compliance to Part of the FCC Rules.

All manuals and user guides at all-guides.com

all-guides.com

Содержание QNW4000

















Отзывы: