Elmo HC7501 Скачать руководство пользователя страница 15

- 14 -

Model

HC7501

Power source

DC12V (DC11V~16V)

Power consumption

Approx.4.2W

Pick-up device

1/2" Color interline-transfer CCD

Effective picture element

768 (H) x 494 (V)

Scanning area

6.45mm (H) x 4.84mm (V)

Scanning system

2:1 interlaced

Scanning frequency

15.734kHz (H), 59.94Hz (V)

Sync. system

Internal/External

Resolution

480 TV lines (Horizontal)   350 TV lines (Vertical)

S/N ratio

More than 50dB

Recommended illumination

120 lx (F1.4 under incandescent lamp)

Minimum illumination

2.0 lx (F1.4 under incandescent lamp, AGC at 18dB)
0.12 lx (F1.4 under incandescent lamp, sens up at 16F)

AGC

Built-in (Factory-set at ON, 12dB)

White balance

AUTO/Manual/Push-set (Factory-set at ON, AUTO)

BLC (Backlight Compensation)

Built-in (Factory-set at OFF)

AES (Automatic Electronic Shutter)

Built-in 1/60 ~ 1/10,000 sec. (Factory-set at OFF)

Electronic shutter

Built-in

1/60  1/100  1/250  1/500  1/1,000  1/2,000  1/4,000  1/10,000 sec.

Frame accumulation

Built-in 64 frame in Auto mode

Menu (On Screen Display)

AGC, White balance, BLC, AES, Electronic shutter, SYNC. Adjust, 
Video adjust, Character

Video Output

VBS 1.0 V(p-p), 75

, NTSC, compatible

Y/C Output

Y: 1.0 V(p-p), 75

C: 0.286 V(p-p), 75

S-VIDEO terminal or 12P terminal

External sync. Input

VBS 1.0 V(p-p), 75

12P terminal

Auto-iris terminal

4P (DC/Video)

Power terminal

4P terminal or 12P terminal

Lens mount

CS-mount/C-mount with 5mm ring

Ambient temperature

-10°C ~ +50°C (14°F~122°F)

Ambient humidity

30% ~ 90%

Dimensions

60 (W) x 60 (H) x 140 (D)mm (2.4 x 2.4 x 5.5 inches)

Weight

410grm (0.9lbs)

SPECIFICATIONS

Note: Weight and dimensions are approximate.

Design and specifications are subject to change without prior notice.

Содержание HC7501

















Отзывы: