1.
Check whether all the hoses, container, secretion cap and bacteria filter are in perfect status. Defected or torn parts should
be changed.
2.
Check whether or not the hose connections are correct, and whether the secretion cap is inserted strongly and the container
is inserted into the motor unit correctly.
3.
Operate LIFETIME SA-PB device. After the device is operated, it starts to function in the lowest vacuum level and shows the
current charge status. By visually checking the capacity indicator, control the charging status. If needed, charge the battery pack
(see the chapter "5.4. Charging LIFETIME SA-PB").
4.
Close the suction piece of the front part with your thumb.
5.
Operate the device and select -650 mmHg which is the maximum vacuum power. LIFETIME SA-PB device should reach this
vacuum power within approximately 10 seconds.
It is understood that the device has reached this vacuum power by applying the following steps:
All the LED lights from –100mmHg to –600mmHg become active stage by stage.
-650 mmHg LED lights flash on and off.
If the device reaches the set vacuum power for more than 10 seconds, it indicates that the suction power is low. Check for possible error
(See the chapter "8. Faults and Troubleshooting".
6.
Open the finger check hole of the end piece.
7.
Close LIFETIME SA-PB device again.
8.
Faults and Troubleshooting
Description of Fault
Underlying Reason
Solution
Device not operating,
O/I
indicator and
capacity indicator band shows the device is
Pump fault
Enable the device to be repaired by the
ready for operation.
manufacturer or authorized specialist.
Fuse fault
Fuse fault in the vehicle socket
Battery group over discharged.
Repeat the charging and discharging
Device not operating,
O/I
indicator shows the
procedures for several times. If the result is
device is ready for operation.
the same, change the battery pack.
Polar connections in the vehicle socket are
Correct the incorrect polar connections and
reverse.
change the fuses if required.
Connection between circle plate and battery
Do the interconnection entirely.
group is not well inserted.
Device is not opened or closed.
Electronic circle fault
Make the device repaired.
There are leakages in the suctioning parts of
Check whether the hose connections, filter
The device cannot reach the maximum
cover and saliva cover be inserted
the device.
vacuum pressure of -650 mmHg for 10
appropriately or not.
seconds, but the capacity indicator band
Battery pack is not sufficiently charged.
Charge the battery pack.
shows the device is ready for operation.
Pump fault.
Make the device repaired by the
manufacturing plant or authorized specialist.
At the -400 mmHg suction level or higher
suction level LED light for -200 mmHg or -300 Bacteria filter is full.
Insert a new filter.
mmHg is continuously active.
Charging procedure is not performed.
External power feeding is so low.
External power feeding should be between
12.0 and 13.8V DC.
Battery pack overheated. Charging is
Make the temperature of the device lower
impossible in the temperatures more than
under +45°C.
+45°C.
Battery pack overcooled. Charging is
Make the temperature of the device higher
impossible in the temperatures less than
Charging procedure is not performed.
over +5°C.
+5°C.
100% LED light is not active when the
Fuses fault.
Make the device repaired by the
charging procedure is completed.
manufacturing plant or authorized specialist.
Fuse in the vehicle socket fault.
Change the fuse.
Connection between circle plate and battery
Do the connection thoroughly.
group is not correct and entire.
The charger does not have the required
Use the original adapter/charger and/or
features.
accessories.
The current supplied by the vehicle electric
Check the vehicle electric installation.
When the charging procedure is over 100%
installation is not between 12.0-13.8 VDC
LED light is not active.
Capacity counter setting is abnormal.
Discharge the device until it automatically
stops and charge it until it is fully filled without
Page
11
/
14
