background image

Test Failures with remote unit
FAILURE

DISPLAY

DESCRIPTION

Miswire

Display the incorrect wiring of 
the end connectors.

Open 

m

Display the broken wire and 
the distance to the break.

Pair Length

m

Indicate that the length of the 
pairs within a cable are 
abnormal different.

Split Pair

A portion of the cable 
assembly has split pairs or a 
poor quality cable.

B). Cable Length Measurment
The tester measures the length of both twisted-pair.  If the 
tester is not calibrated to the cable under test, then factory 
default cable characteristisc are used to compute the length.  

If a more accurate length measurement is desired, refer to 
“CALIBRATING CABLE LENGTH” described on this manual.
Before a length measurement is made, the tester performs 
“Test Cables” described in this manual to prevent any cable 
failures from corrupting the length measurement.
Cable length measure procedure.
1. Select cable type under test.
2. Connect the cable and test to the appropriate connector on 
the tester.
3. Press LENGTH key.
4. Use ▼or ▲key to scroll selection multiple displays.
The information that is displayed depends on the type of cable 
selected.  For twisted pair cable, each pair has corresponding 
length measurement.
A 5% difference in length botween pairs, is uncommon.

For 50m UTP  

m

  

m

m

  

m

C). WIRE MAP CHECKING
Use the tester wiremap function and remote identifier unit (ID), 
to determine the wiring status of both the near end and far end 
of the cable.

Содержание 46









Отзывы:

Похожие инструкции для 46