ELM 329 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 83

ELM 329 Скачать руководство пользователя страница 58

58 of 83

ELM329DSC

Elm Electronics – Circuits for the Hobbyist

www.elmelectronics.com

ELM329

CAN Input Frequency Matching

Most modern vehicles have a CAN network

connected to pins 6 and 14 of the OBD connector. At
one time, however, the use of these pins was left to
the vehicle manufacturer, and a number of different
systems were connected to them.

In order to prevent the disruption of any connected

systems while the ELM329 is searching for a protocol
(it sends out requests during a search), the ELM329
now performs several tests on these wires. Prior to
firmware version 2.1, the tests simply looked for
activity on the wires but were not frequency selective.
This meant that, for example, vehicles that had a
speedometer signal connected to either pin might see
a disturbance during a protocol search. The new
firmware actually measures the input frequency and
requires that it matches that of the selected CAN
protocol before any test message can be sent.

The diagram below shows how the logic works. It

may seem a little complicated, but what it really says is

that for the default settings, a send is allowed if the
input signal frequency matches the CAN setting, or if
there appears to be no signal. In addition, if the user is
trying a non-standard OBD frequency, but a standard
frequency is received, a send will not be allowed.

All bits of PP 28 are set to 1 by default, but may be

changed at any time (see the Programmable
Parameters section).

This logic is only used while searching for a valid

protocol. Once a particular protocol is considered to be
active, no further frequency checks are made (as it is
too time consuming). Note that if you should use the
AT BI command to bypass the initiation process, this
frequency matching test will also bypassed.

Signal

Processing

allow a
CAN send

CAN Rx

(pin 24)

signal is 500 kbps

setting is

500 kbps

PP 28, b7 is 0

signal is 250 kbps

setting is

250 kbps

PP 28, b6 is 0

signal is not 250 or 500 kbps

setting is not

250 or 500 kbps

PP 28, b0 is 1

input is quiet

Send Logic While Searching for a Protocol

«
...
56
57
58
59
60
...
»

Содержание 329




















































































Отзывы:

Нет отзывов