Ellington E-WOD52ABZ5C Скачать руководство пользователя страница 7

page 6

7. Wiring.

CAUTION

Be sure outlet box is properly grounded 

and that a ground wire (

GREEN

 or Bare) is present.

Make sure all electrical connections comply with 
Local Codes or Ordinances and the National 
Electrical Code. If you are unfamiliar with electrical 
wiring or if the house/building wires are different 
colors than those referred to below, please use a 
qualified electrician.

Note

Excess lead wire length from the fan can be 

cut to the desired length and then stripped.

DANGER

:  If using this fan in a WET or DAMP 

location, this fan must be connected to a supply 
circuit that is protected by a Ground Fault Circuit 
Interrupter (GFCI) to reduce the risk of personal 
injury, electrical shock or death.

When downrod is secured in place on the 
hanging bracket, electrical wiring can be made as 
follows:
Connect 

BLACK

 and 

BLUE

 wire from fan to 

BLACK

 wire from ceiling with wire connector 

provided.
Connect 

WHITE

 wire from fan to 

WHITE

 wire 

from ceiling with wire connector provided.
Connect all 

GROUND 

(

GREEN

) wires together 

from fan to 

BARE

/

GREEN

 wire from ceiling with 

wire connector provided.

If you intend to control the fan light with a 
separate light switch, connect 

BLUE

 wire from fan  

to the 

BLACK

 supply from the independent 

switch. 

* Wrap each wire connector separately with 
electrical tape as an extra safety measure.

8. Canopy Assembly.

canopy

hanging bracket

black

black

white

white

blue

black supply wire

ground

(green

or bare)

white supply wire

*

from ceiling

from fan

ground 
(green or bare)

hanging bracket

This fan is remote control adaptable (remote 
control sold separately). 

Note

: Only remote 

controls approved for WET locations can be used 
with this fan.

wire connector

wire 
connectors

Temporarily raise canopy to hanging bracket to 
determine which 2 screws align with slotted holes in 
canopy, and then lower canopy and 

partially loosen

 

these 2 screws.  

Remove

 the 

other

 2 screws and set 

aside.

Now, lift canopy to hanging bracket again, aligning 
slotted holes in the canopy with loosened screws in 
hanging bracket. Twist canopy to lock. Re-insert the 
other 2 screws and secure all screws with Phillips 
screwdriver.

Содержание E-WOD52ABZ5C












Отзывы: