Elkron MP500/16 страница 14 Скачать руководство пользователя

Страница: 14 / 140

MP500/4N-8-16 Programming

1.2.1

Function keys

Symbol

KP500DP/N - KP500D/ST key

Associated function

Silent panic indication

Emergency indication

Fire indication

Clean glass

Table 6 - KP500DP/N

– KP500D/ST keypad function keys

1.2.2

Status icons

Figure 4 - KP500DP/N

– KP500D/ST keypad display and status icons

The LEDs and icons on the keypads indicate system status and alarms. Available information is shown in

Table 7 - LED and icon

indications of KP500DP/N

–

KP500D/ST keypad

The amount of displayed information depends on the system status level (armed or disarmed), the EN50131 grade set during
programming and the access level (see paragraph

2.1

System access codes

). Paragraph

1.2.2.1

Use of LEDs and icons with EN50131

grade 3

lists the information available in the various cases.

Symbol

Description

Supplied indications

Power

Present

= no mains power

Highlighted

= see electric mains failures details

Failure

Present

= failures present

Highlighted

= see details of current failures

Timed programmer

Present

= commands present for the current day

Highlighted

= control activation warning

Open inputs

Present

= open input

Highlighted

= see details of current open inputs

Inhibited or

isolated inputs

Present

= inhibited or isolated input

Highlighted

= see details of current inhibited or isolated inputs

Alarm

Present

= at least one alarm condition present

Highlighted

= see details of current alarms

Tamper

Present

= at least one tamper condition present

Highlighted

= see details of current tampering

Table 7 - LED and icon indications of KP500DP/N

– KP500D/ST keypad

Содержание MP500/16













































































































































Результаты поиска

Содержание MP500/16

Отзывы:

Похожие инструкции для MP500/16

Бренды по названию

Популярные бренды

Elkron MP500/16, Руководство по программированию

Результаты поиска

Содержание MP500/16

Отзывы:

Похожие инструкции для MP500/16

Бренды по названию

Популярные бренды