NVE51586-02
04/2020
4/4
en
SmartRelay Puck 10AX
Prerequisites
Download the ELKO Smart app to your smartphone /
tablet, and install the ELKO SmartHUB to configure and
control ELKO Smart devices.
Additional system information
Detailed product information is available online
in the
system
user guide
: Scan the QR code
or follow the link.
For your safety
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR
ARC FLASH
Safe electrical installation must be carried out
only by skilled professionals. Skilled professionals
must prove profound knowledge in the following
areas:
•
Connecting to installation networks
•
Connecting several electrical devices
•
Laying electric cables
•
Safety standards, local wiring rules and regulations
Failure to follow these instructions will result in
death or serious injury.
Getting to know the product
The SmartRelay Puck 10AX (hereinafter referred to as
puck
) is used to switch the ohmic, inductive or capacitive
loads.
The puck must not be used to control safety
relevant applications.
Control options
Home control:
To control the puck in your home
through the
ELKO Smart app
, you will need the ELKO
SmartHUB.
Room control:
To control the puck through other ELKO
Smart devices, it can be paired. ELKO Smart devices
has to be in the same Zigbee network.
Direct operation:
The puck can always be controlled
directly on-site. To do this, you can connect a maximum
of 10 mechanical push-buttons.
Functions:
•
Switching
•
Setting a timer or a time schedule (via App)
Choosing the installation
location
If you place the puck behind a mechanical
push-button, use a deep installation box.
Connection elements
A
Switch contact
B
Live conductor
C
Neutral conductor
D
Extension unit input 1
E
Unused
Mounting the puck
DANGER
HAZARD OF ELECTRIC SHOCK
•
Make sure that the terminal connection area does
not come in contact with the metallic parts of any
device installed in the same location.
•
Do not short the outputs to neutral.
•
The switch contact and live conductor connection
must be separated from one another by a 240 VAC
basic insulation.
Failure to follow these instructions will result in
death or serious injury.
Connecting the puck
DANGER
RISK OF ELECTRIC SHOCK, EXPLOSION OR
ARC FLASH
•
When working on the device, always disconnect
the device from the power supply, as the output
may carry electrical current even when the load is
switched off.
•
Turn off the fuse in the incoming circuit before
installation, maintenance, or service (or
replacement of the load) of the device.
Failure to follow these instructions will result in
death or serious injury.
Operating elements
F
Status LED
G
Setup/Reset button
H
Test button
Setting the puck
WARNING
DANGER DUE TO ELECTRIC SHOCK
•
Observe the regulations for working on live parts.
•
Only actuate the device buttons using insulated
auxiliary equipment that meets the requirements
of EN 60900
Failure to observe these instructions can lead to
death or serious injury.
|
Testing the puck
Before you couple the puck or connect mechanical
push-buttons, you can test the basic functions.
Connecting to the ELKO
SmartHU
B
Short press (< 0,5 s) the Setup/Reset button 3 times
to connect to the available Zigbee network. Upon
successful connection to the ELKO SmartHUB
the
status LED turns green.
Pairing to other ELKO Smart devices
To control the product in a room control mode, it can be
paired with other ELKO Smart devices within the same
Zigbee network.
For more details, refer to the system
user guide.
Resetting the puck
Short press (< 0,5 s) the Setup/Reset button 3 times
and then long press the Setup/Reset button once for
>10 s and <15 s to reset the puck to factory default
mode.
All configuration data, user data, and network data is
deleted. After which:
•
No connectivity to other devices or rooms
•
No timer settings
Operating the puck
You can remotely control the puck through the
ELKO
Smart app
.
Behaviour of the status LED
Refer to the system user guide.
Troubleshooting
Refer to the system user guide.
Technical data
Nominal voltage
AC 220-240 V, 50/60 Hz
Nominal power
Nominal current
10 AX
Switching channel
1, dry contact
Standby
Maximum 0.3 W
Operating
Temperature
0 ºC to 35 ºC
Neutral conductor
Required
Connecting
terminals
Maximum 2
2.5 mm
2
,
solid or stranded types
Extension
connection
Maximum 10 mechanical
push-buttons
Length of all cable
sections
Maximum 50 m for 3-wire
NYM cable
Fuse protection
16 A circuit breaker
IP rating
IP20
Frequency band
2.4 GHz
Transmission
capacity
Maximum 2.5 mW
Product
dimensions
(H
×
W
×
D)
43
43
22 mm
Wall box dimension
|
The wall box must
have a minimum
depth of 26 mm.
Certification
Zigbee 3.0
Dispose of the device separately from
household waste at an official collection point.
Professional recycling protects people and the
environment against potential negative effects.
Trademarks
•
Zigbee
®
is a registered trademark of the Zigbee
Alliance.
•
Apple
®
and App Store
®
are brand names or registered
trademarks of Apple Inc.
•
Google Play
™
Store and Android
™
are brand names
or registered trademarks of Google Inc.
Other brands and registered trademarks are properties
of their relevant owners.
EU Declaration of conformity
Hereby, ELKO, declares that this product is in
compliance with the essential requirements and other
relevant provisions of RADIO EQUIPMENT DIRECTIVE
2014/53/EU. Declaration of conformity can be
downloaded on: ELKO.no.
ELKO
ELKO AS, Sandstuveien 68, 0680 Oslo
Phone.: +47 67 80 73 00 - E-mail: [email protected]
Pb. 6598 Etterstad, 0607 Oslo
www.elko.no
http://proff.elko.no/elko-smart
ELKO Smart
EKO07144
en
fi
nl
sk
es
hu
en
da
nl
2200 W
2000 W
500 VA
1000 VA
200 W
100 W
1050 VA
10 A, 140 μF
C
22 mm
43 mm
43 mm
1
L N
L
F G H
3 × < 0,5 s
3 × < 0,5 s +
1 × 10 s
×7
16 A
L
N
1
L N
L
1-2 x 1.5 mm²
1-2 x 2.5 mm²
Maksimum 0.5 Nm
1
L N
L
11 mm
A
C D E
B
