PAGE 2
FD700_3_2JJO, FD700_5_2JJO
1000003126 (Rev. A - 12/15)
Installation
For correct and safe installation, please read these instructions completely.
• All Installation work must be performed by an authorized service personnel.
• Disconnect electrical supply serving the Installation area to reduce risk of electrocution.
• Unit not suitable for installations where water jets could be used.
DANGER
WARNING
• Shut off water supply serving the Installation area to reduce risk of water damage.
• Ensure proper ventilation by maintaining clearance from cabinet louvers to wall on each side of Cooler as specified in Rough-In.
• Never wire compressor directly to electrical supply.
• Do not solder tubes inserted into the In-line Strainer as damage to the o-rings may result.
• Thoroughly flush all water lines and fittings of all foreign matter before connecting to Cooler.
• Warranty is void if the plumbing kit or glass filler is not specified for use by the Manufacturer for this particular model.
• Warranty is void if Installation is not made in accordance with current Manufacturing instructions.
CAUTION
• Hose-sets are not to be used for connecting to water mains.
• If inlet pressure is above 100 psig (0.69 MPa), a pressure regulator must be installed in water supply line. Any damage caused by
reason of connecting this product to water supply line pressure outside its rated pressure, is not covered by warranty.
• This cooler is manufactured in such a manner that it does not in any way cause taste, odor, color, or sediment problems. If a taste,
odor or sediment problem is prevalent, try installing our water filter on the supply line.
• Tools/Items required but not provided.
o Water Shut-off Valve with 3/8” (9.5mm) compression outlet.
o 1-1/4" (31.8mm) Waste Trap (non-metallic)
o Safety Glasses
o Protective Gloves
o 5/16" (7.9mm) Hex Driver or Flathead Screwdriver
o C-13 Modular International Power Cord Set
Installation: Cooler Mounting
1.
Select installation location. Installation location must be a flat surface. Installation location should ensure proper ventilation by maintaining 4"
(102mm) minimum clearance from cabinet louvers to wall.
2. Remove front panel (Item 26) by unscrewing (2) 5/16" (7.9mm) Hex Head screws. Set panel aside.
3. Installation area must also include water supply, electrical supply and suitable drain. Water, drain and electrical supply systems must comply
with local code requirements.
Installation: Water Line connection
1. Ensure Mains Water Supply has Water Shut-off Valve with 3/8” (9.5mm) compression outlet.
2. Connect loose end of supplied 3/8” (9.5mm) unplated copper tube to Water Shut-off Valve. See Figure 1.
•
NOTE: If 3/8” (9.5mm) copper tube must be cut for proper fit, remove all burrs from the outside of tube and re-flush before use.
3. Install waste trap. Remove the slip nut and gasket from the waste trap and install them on the Cooler waste line making sure that the end of the
waste line fits into the waste trap. Assemble the slip nut and gasket to the trap and tighten securely.
4. Turn on building water supply and open Water Shut-off Valve. Check all connections for leaks and correct any found.
Installation: Electrical connection
1. Rotate fan to insure proper clearance and free fan action.
2. Connect modular (C-13) end of International Power Cord Set (sold separately) into Power Inlet on unit and ensure plug-end reaches electrical
outlet. Do not plug into electrical outlet!
NOTE: WATER FLOW
DIRECTION
BUILDING WATER SUPPLY
WATER SHUT-OFF VALVE
(NOT PROVIDED)
1/4" O.D. TUBE
WATER INLET
3/8" (9.5mm) O.D.
UNPLATED COPPER TUBE
IN-LINE
STRAINER
(PROVIDED)
Figure 1
Figure 2
A = White (Neutral)
B = Black (230Vac)
C = Ground (Earth)
D = Fan
E = Freeze Control (when provided)
F = Cold Control (Water)
G = Hot Tank Switch (When Provided)
H = Hot Tank (when provided)
I = Capacitor (when provided)
POWER INLET