background image

JA09252018 

www.elitescreens.com 

 

 

 

 

 

 
 

 

Evanesce Tab-Tension B CineGrey 5D®

 

 

Recessed In-Ceiling Ambient Light Rejecting Projection Screen 

 

User’s Guide

 

 

 
 
 
 
 
 
 
 
Congratulations

  on your  new 

Evanesce  Tab-Tension  B  CineGrey  5D

  purchase! The  screen material  included  is 

our  award  winning 

ISF  Certified

 

CineGrey  5D™  which  is  a  front  projection  material,  precisely  formulated  for 

environments  with  minimal  control  over  room  lighting.  It  was  designed  to  enhance  picture  brightness,  offer 

accurate  color  fidelity,  and  improve  contrast  levels.  The  CineGrey  5D™  is  best  for  family  rooms,  educational 

facilities, conference rooms, house of worship or any applications in which incident light is a factor.  
 
 
In order for the CineGrey 

5D™ to maintain its projection qualities and optimum performance please refer to the 

list below for proper maintenance and cleaning.  
 

• Use a dry microfiber cloth to remove dust from the screen’s surface. 

 

• When cleaning, use a damp microfiber cloth wit

h warm water to remove any marks.  

• Never rub or apply pressure when cleaning the surface. 

 

• Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface. 

 

• In order to avoid damaging the screen, avoid touching it directly wi

th your fingers, pens/pencils or any 

other sharp or abrasive objects. 

 
 
 

This Product is Designed for Integrators 

This user manual is written for the comprehension of licensed professional 

installers/integrators experienced in building and electrical wiring codes. 

 

DIY “do 

-it-

yourself” enthusiasts should consult a professional for assistance

 

 

Содержание Evanesce Tab Tension B CineGrey 5D









Отзывы: