background image

11152019-JA 

www.eliteproav.com

 

 

 

 

Pro Frame Thin UST Series 

EDGE FREE

®

 Ceiling/Ambient (CLR

®

/ALR) Light Rejecting  

Ultra-Short Throw Fixed Frame Screen

 

USER’S GUIDE 

__________________________________________________________________________________ 
 
Product Description:  

The 

Pro Frame Thin UST Series 

is an ultra-short throw fixed frame projection screen that uses Elite ProAV’s 

EDGE  FREE

®

  technology.  It  is  designed  for 

Ultra

-

Short  Throw  Projectors  only, 

for  use  in  environments 

where  ceiling  light  cannot  be  entirely  controlled

It  includes  an  LED  backlight  kit  and  an  ultra-thin  bezel  to 

further enhance the frame appearance. 

Screen Maintenance 

Dust, dirt and scratches on the projection screen surface will affect the quality and performance of the 
projection image. For optimal results we advise to pay attention to the following instructions. 

 

1) The screen surface has a horizontal lens structure. 

DO NOT

 wipe the screen up and down or in a circular 

motion. 

Wipe very gently from left to right only

 
2) Please clean the dust on the screen surface with a soft brush or microfiber cloth (rough towel or cloth 

may damage the screen’s surface). 

 
3) Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water. 

 
Notes

The following precautions should always be followed to avoid damaging the material, 

which is not covered under warranty. 

 

Don’t 

touch

 the screen material to avoid leaving fingerprints. 

Use gloves when handling the material

 

 

Don’t 

scratch

 the material, as it will leave permanent markings on the screen’s surface. 

 

 

Don’t 

point 

to the screen material with a fingertip or other sharp objects to prevent damage to the 

material. 

 

 

Don’t 

use

 acetone, benzene, alcohol and any other organic solvents to clean the screen material. Using 

such chemicals will permanently damage the screen. 

 

Содержание EDGE FREE Pro Frame Thin UST Series









Отзывы: