Eliminator Lighting FUR128 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 26

Eliminator Lighting FUR128 Скачать руководство пользователя страница 7

S A F E T Y G U I D E L I N E S

This unit may “pop” the fuse if the maximum allotted load of 3 amps is reached.

• To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture.

• Do not spill water or other liquids into or on to your unit.

• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is

used to reduce the risk of electrical shock and fire in case of an internal short.

• Do not attempt to operate this unit if the power cord has been frayed or broken.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user serviceable parts inside.

• Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6”

(15cm) between this device and a wall.

• Do not attempt to operate this unit if it has been damaged in any way.

• This unit is intended for indoor use only. Use of this product outdoors voids all warranties.

• During long periods of non-use, disconnect the unit’s main power.

• Always mount this unit in safe and stable matter.

• Power cords should be routed so they are not likely to be walked on, pinched by items placed

upon or against them.

• Cleaning - The fixture should be cleaned only as recommended by the manufacturer. See the

Maintenance Guidelines section of this manual for cleaning details.

• Heat - The appliance should be situated away from heat sources such as radiators, heat regis-

ters, stoves, or other appliances (including amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into, the unit.

C. The unit has been exposed to rain or water.

D. The unit does not appear to operate normally or exhibits a marked change in performance.

7

«
...
5
6
7
8
9
...
»

Содержание FUR128



























Отзывы:

Нет отзывов