manualshive.com logo in svg

Elgo LIMAX33 CP-00 SERIES, Руководство владельца и по безопасности, Страница: 69 / 92

Поделиться
Скачать
Elgo LIMAX33 CP-00 SERIES Скачать руководство пользователя страница 69

 

 

 

 

Safety Functions 

- 69 - 

13.2.8

 

Relations limit switches/Offsets/ETSL and reference positions (summary) 

Figure 23 (below) illustrates the lower final limit switch, the lower pre-triggered stopping limit, the lower inspec-
tion limit and the distance s for ETSL-calculation when moving down related to the lower (limit switch-) reference 
position. 
 

 

Figure 23: Relations to the lower reference position 

 
Relations to the upper reference positions see Figure 24 on next page. 

 

 

Lower 

reference 

position 

car buffer

counterweight buffer

car 

counter

weight

Offset 

ETLS_DOWN

Distance „s“ for 

ETSL calculation

Lower 

limit switch

Offset lower 

limit switch

Offset lower

inspection 

limit switch

Lower inspection 

limit switch

Lower pre-triggered 

stopping limit position 

The lower 

reference position 

will normally be 

learned when the 

car is placed  on 

the buffer

car buffer

counterweight buffer

car 

counter

weight

Содержание LIMAX33 CP-00 SERIES





























































































Отзывы:

Нет отзывов