ELGO Electronic LIMAX02 Series Скачать руководство пользователя | Manualshive

Страница: 13 / 40

background image

Installation and First Start-Up

- 13 -

5.2

Description installation of the Sensor

5.2.1

Installation Principe

Figure 5: Installation with tension weight

Figure 6: Installation with dowel and spring

LIMAX02 can be installed at any position in the shaft, depending on spatial conditions and layout of the particu-
lar elevator installation.

The magnetic tape is installed freely suspended in the shaft. It can be fixed with the RMS mounting kit (available
as option) on the guide rail. Alternatively fixation in the shaft head is either on beams or directly bolted into the
ceiling. The necessary tension in the tape is provided by a tension weight of about 5 kg. A sway guard at the
bottom will keep the tape from swaying in an uncontrolled position. Alternatively the magnetic tape can be ten-
sioned by a spring.

The sensor head can be mounted onto the cabin or cabin frame, depending on the spatial conditions of the
elevator.

Sensor

Magnetic tape

Guide rail

Upper tape fixation

Tension weight

Sway guard

Upper tape fixation

Sensor

Magnetic tape

Spring

Guide rail

«
...
11
12
13
14
15
...
»

Содержание LIMAX02 Series









































Отзывы:

Нет отзывов

Похожие инструкции для LIMAX02 Series

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 2

Бренд: YASKAWA Страницы: 251

Бренд: Avermedia Страницы: 1

PROFI BUS Multiturn 5868 Series

Бренд: Sendix Страницы: 22

Бренд: LEGRAND Страницы: 4

Бренд: Moxa Technologies Страницы: 2

Бренд: IMO Страницы: 94

Бренд: iLive Страницы: 12

Бренд: Nibe Страницы: 76

Бренд: Patton electronics Страницы: 10

Бренд: TC Communications Страницы: 31

Бренд: Advantech Страницы: 4

Бренд: Kaco Страницы: 42

Бренд: AtmosFX Страницы: 15

Бренд: MEMUP Страницы: 14

Бренд: DROPSA Страницы: 8

Бренд: Data Connect Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды