manualshive.com logo in svg

Elgar Sorensen DCS 3kW Series, Руководство по эксплуатации

Поделиться
Скачать
Elgar Sorensen DCS 3kW Series Скачать руководство пользователя страница 18

Installation 

Sorensen DCS Series 3kW Supplies 

2.2.2 

2.2.3 

2.2.4 

2.3 

AC Source Grounding 

Ensure the power supply is connected to an appropriately rated AC outlet with the 
recommended AC input connector as set out in 

Section 2.5 AC Input Power Connection

. 

There is a shock hazard if the power supply chassis and cover are not connected to an 
electrical ground via the safety ground in the AC input connector. The third wire in a single 
phase AC input connector and the fourth wire in a three phase AC input connector must be 
connected to an electrical ground at the power outlet. Any disconnection of this ground will 
cause a potential shock hazard to operating personnel. 

This power supply is equipped with an AC line filter to reduce electromagnetic interference and 
must be connected to a properly grounded receptacle, or a shock hazard will exist. 

Operating the supply at line voltages or frequencies in excess of those specified may cause 
leakage currents in excess of 5.0 mA peak from the AC line to the chassis ground. 

Operating and Servicing Precautions 

Exceeding the maximum model-rated input voltage may cause permanent damage to the unit. 

Always disconnect power, discharge circuits, and remove external voltage sources before 
making internal adjustments or replacing components. When performing internal adjustments or 
servicing the power supply, ensure another person with first aid and resuscitation certification is 
present. Repairs must be made by experienced technical personnel only. 

Be sure to isolate the power supply from the input line with an isolation transformer when using 
grounded test equipment, such as an oscilloscope, in the power circuit.  

The power supply must not be operated where flammable gases or fumes exist. 

Parts and Modifications 

Do not use substitute parts or make unauthorized modifications to the power supply to ensure 
that its safety features are not degraded. Contact the manufacturer for service and repair help.

 

Initial 

Inspection 

On first receiving your DCS Series power supply, perform a quick physical check, paying 
particular attention to front panel controls and indicators as well as rear panel connectors and 
terminals. See 

Figure 1-1

 and 

Figure 1-2

 for front and rear panel diagrams.

 

2-2 

Operation Manual 

Содержание Sorensen DCS 3kW Series


















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды