ELEXOL Ether I/O 24 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 38

ELEXOL Ether I/O 24 Скачать руководство пользователя страница 10

Ether I/O 24 Users Manual V1.3

Elexol Pty Ltd Version 1.3

Page 10

http://www.elexol.com

E L E

X O L

E L E C T R O N I C

S O L U T I O N S

Home, Office and Building Automation, Distributed control and Internet
Connectivity

Because of its low cost per I/O line, the Ether I/O 24 module ideally services the budget
sensitive building automation market. Ethernet’s low cost infrastructure, cabling and
switching systems combined with the ability of the Ethernet network to service other
systems within a building make it a single platform multi function network for delivering
services throughout a building.

Ethernet networks can be used to deliver Voice Over IP telephony services, Internet and
Local Area Network services, Video and Audio on demand as well as control and
monitoring of devices or services within the building. With IP becoming the new
standard for worldwide communication and most modern buildings being fitted with
Ethernet cabling during construction, the Ether I/O 24 can economically share that
infrastructure and optimize connectivity.

The Ether I/O 24 in conjunction with the accessory boards can be used to control most
electrical devices. Future expansion of the accessory board range will allow additional
devices to be serviced by the module.

The falling costs of PC computing power combined with the fact that most new PC
hardware is equipped with an Ethernet port make the PC platform combined with
Ethernet connectivity ideal for central control of most mid to large scale systems. When
linked to the Internet, an automated building can be controlled and monitored from any
Internet terminal; Internet enabled mobile phone or other device anywhere on the globe.
Wireless connectivity will further enable the occupant to access their entire buildings
network facilities without the burden of wires.

The low power consumption of the Ether I/O 24 module will enable the module to reduce
the additional cost burden of building automation on the utility bill. In many cases an
automated building may have a reduced utility bill through more efficient use of power.
Load shedding during peak demand times will allow building designers to purchase
energy at lower rates and electricity supply companies to make more efficient use of their
infrastructure.

When connected to a router or if the main control PC has Internet access the system is
able to request its own maintenance or repair when a malfunction occurs. When a unit has
run its scheduled number of hours it can automatically contact the building supervisor or
contracted maintenance organization to arrange for service. By automating these services,
the chances of maintenance being overlooked and expensive malfunctions and downtime
resulting will be minimized. When a fault does occur, downtime can be minimized by
prompt, automatic notification to the correct people.

«
...
8
9
10
11
12
...
»

Содержание Ether I/O 24







































Отзывы:

Нет отзывов