elero RolMotion M, Инструкция по эксплуатации и сборке, Страница: 5 / 10

Removing and inserting the motor cable plug
Delivery con-
dition
Removing plug Inserting plug
Fig. 4 Removing and inserting the motor cable plug
5.3 Connection example for RolMotion M
230 V / 50 Hz
1 0 2
reseau electrique
L
N
PE
230V/50Hz
ver
t-j
aune
br
un
no
ir
ble
u
de volet
M
1~
1 0 2
rete
L
N
PE
230V/50Hz
ver
de
/g
ial
lo
m
ar
rone
ner
o
blu
M
1~
1 0 2
Netz
L
N
PE
230V/50Hz
gr
ün/
gel
b
br
aun
sc
hw
ar
z
bla
u
oder -taster
M
1~
1 0 2
power grid
L
N
PE
230V/50Hz
gr
ee
n/
Yel
low
br
own
bl
ac
k
blu
e
junction box
M
1~
boiter de scatola di
derivatione
(3)
(2)
(1)
(3)
(2)
(1)
Fig. 5 Connection diagram RolMotion M 230 V / 50 Hz
and cable assignment when using Hirschmann plug
connection STAS-3
Important
The motor controls in the Open and Down/Closed travel
directions must be locked against each other.
A switching time of at least 0.5 seconds must be observed.
5.4 Parallel circuit
Important
You can connect up to 3 (maximum) RolMotion M in
parallel. Please note the maximum switching capacity of
the control unit.
However, the behaviour of the devices is not synchronous.
Do not connect the RolMotion M drive in parallel with other
drives (e.g. elero RolTop M).
5.5 Commissioning
Important
The drive is in commissioning mode when delivered.
► The end positions must be adjusted using the
elero
assembly cable (see Fig. 6).
► The assembly cable may only be connected to
commission the drive and for adjustment operations
→
1
→
2
→
3
5.5.1 Connection for assembly cable
%ODX1HXWUDOOHLWHU
6FKZDU]
%UDXQ
*UQJHOE
HOHUR HOHUR
:KLWHQHXWUDOFRQGXFWRU
%ODFN
5HG
*UHHQ
Fig. 6 Connection for assembly cable
► Switch on mains.
► You can now set the end positions with the elero
assembly cable.
5.6 Setting the end positions
Important
To use travel profiles, the upper and lower end positions
must first be set. First program the upper end position,
then the lower end position.
The end positions and the strain relief are set
• via the
elero assembly cable (ensure correct connection
according to chapter 5.5.1)
5.6.1 Changing/deleting the end positions
It is not possible to change or delete individual end
positions. This is always done in pairs (upper and lower end
position simultaneously).
Before you can change or delete the end positions, the
power supply must first be interrupted.
After a brief disconnection from the power supply, the end
positions can be deleted within 5 minutes.
Changing/deleting the end positions
1
Restore the power supply after the mains have been
switched off.
2
Starting from a central blind position, use the as-
sembly cable to simultaneously press both direction
buttons [ UP ▲]+[ DOWN/CLOSE ▼], and hold them
down until the drive briefly moves up and down.
The end position settings have been deleted.
The end positions may be readjusted.
5.6.2 Four variants of end position settings
Four different end position settings are possible. These can
be clearly selected according to the technical requirements
of the blind.
End position settings
(4 variants)
possible with
A Upper and lower end
position freely adjustable
Suspension spring,
tapes, belt
B Fixed upper limit stop,
lower end position freely
adjustable
T-straps, tapes, belt,
limit plugs, angle
bracket
C
Fixed upper and
lower limit stop
Anti push-up device,
rigid shaft connectors,
limit plugs, angle
bracket
D Upper end position freely
adjustable, fixed lower limit
stop
Anti push-up device,
rigid shaft connectors
© elero GmbH EN | 5
Assembly | Electrical connection | Adjusting the end positions