DoorControl
3
Functions
➱
Motor run time monitoring
DoorControl includes programmable motor run time moni-
toring which automatically switches the drive off in the
event of excessive motor run time. In order to programme
the motor running time the drive should be taken to the
CLOSE door position.
Set DIP I to the ON position. Briefly press programming
button S3, LED 2 illuminates, now move the drive in self-
retention until reaching the limit switch door OPEN. LED2
goes out, the motor run time is now programmed.
.
If the programming button S3 is pressed for more than
5 secs. (LED2 goes out) the run time monitoring is reset
to the maximum value (0 secs.).
➱
Locking mechanism for the door edges (OSE or 8,2 kOhm)
Should the locking mechanism for the door edges be activa-
ted during a CLOSING movement, the control switches over
to the opening direction (reversing or free movement). If the
CLOSE pre-limit switch is pressed, the drive is stopped. If the
locking mechanism for the door edges is faulty, the drive can
be operated with the built-in touch keyboard and the exter-
nal triple switch in dead man operation.
➱
Light barrier
If the light barrier is activated during a CLOSING move-
ment, the control switches over to the opening direction
and the drive moves up to the OPEN end position. When
the automatic closing mechanism is switched on, the hold-
open time is reinitiated. Should the installation be in an
intermediate position and the light barrier is activated, the
opening direction is started.
➱
Radio remote control Channel 1
The integrated or the internally pluggable radio receiver, as
well as the external input FS (terminal 13+14) change
function with each activation.
(Switching sequence UP-STOP-DOWN-UP. . .)
When the automatic closing mechanism is switched on the
radio remote control always switches on the opening
direction. With each subsequent command, the hold-open
time is reinitiated.
The programming must be based on the radio remote
control in use.
➱
Radio remote control Channel 2
Relay K3 can be additionally controlled with the second
channel.
➱
Automatic closing mechanism
The automatic closing mechanism can be swit-
ched on and off with the rotary switch S2.
When the automatic closing mechanism is
switched on, the preliminary warning time swit-
ches on for approximately 5 secs. at the end of
the hold-open time. The closing procedure is then started.
The door can be opened with the “On” timer contact (terminal 10 a
and closed again with “Off” by the adjusted automatic door-edge
security system.
If the locking mechanism for the door edges has been
activated 3 times before reaching the CLOSE limit switch
the automatic closing mechanism becomes inactive
.
Level 0
Active red traffic light and error message
Level 1
Active red traffic light, error message flashing
Level 2
Automatic closing function on, “hold open” time 10 se
Level 3
as above 20 seconds
Level 4
as above 30 seconds
Level 5
as above 40 seconds
Level 6
as above 50 seconds
Level 7
as above 60 seconds
Level 8
as above 60 seconds (after the light barrier
is CLOSED, the “hold open” time reduced
by approx. 4 secs)
Level 9
Automatic closing function on, “hold open” time 10 sec
LED diagnosis
LED 5 (red)
Stop button activated (terminals 9+10)
LED 4 (red)
Light barrier activated
LED 3 (red)
Illuminates when the locking
mechanism for the door edges is
faulty or activated
LED 2 (yellow) Programme motor run time /
radio reception
LED 1 (green) Power (operating voltage)
Flashes during OPEN and CLOSE
movement
Flashes when the hold-open time runs out
LED 1 (green)
+ LED 3 (red)
Flashes when the running time is exceeded
mains 230V/AC
M
1~
-
+
OUT
Safety
switch
error message
Red traffic light or
Light or
green traffic light
Light or failure notification
with latching relay
Emergency
stop
Triple switch
Stop
Up
Down
pull switch
Radio remote
control,
Light barrier
closing direction
Terminals 15/17
max. 150 mA
Fraba OSE
GN
BN
WS
R 8,2 kOhm
Pre-limit switch CLOSE
or
locking mechanism for the door edges
max. 10A
Fuse on site
21 22
N
PE
PE
N
L
1
2
3
4
5
6
7
8
10
9
12
11
17
15 16
K3
L
N
PE
L
PE
N
8
7
K3
13 14
19
18
20
20
18 19
inputs/outputs
operating elements
Safety devices
Neutralization
24V DC inputs/outputs
230V AC
Terminal diagram DoorControl
230 V/max. 60 W
10 11
Timer
max. 230 V/60 W