Elenco Electronics AM/FM-108CK Скачать руководство пользователя страница 32

Страница: 32 / 56

-31-

QUIZ - AM SECTION

INSTRUCTIONS: Complete the following examination, check your answers carefully.

Answer

1. D

, 2. D

, 3. A, 4.

A, 5. C

, 6. A, 7.

D, 8.

A, 9. B

, 10. D

1. The number of cycles produced per second by a

source of sound is called the ...

A) amplitude.
B) vibration.
C) sound wave.
D) frequency.

2. The radio frequencies used by AM broadcast

stations are between ...

A) 20kHz and 400kHz.
B) 5kHz and 20kHz.
C) 2400kHz and 6000kHz.
D) 550kHz and 1600kHz.

3. The process of removing the audio wave from

the radio wave is called ...

A) demodulation.
B) frequency reduction.
C) modulation.
D) vibrating.

4. When an electromagnetic wave (modulated radio

wave) passes an antenna, it ...

A) induces a voltage and current in the

antenna.

B) changes an audio wave into a radio

wave.

C) changes the carrier frequency.
D) produces sidebands.

5. The power of the signal transmitted by the

broadcast station and the distance, the signal
travelled from the transmitter to the receiver,
determine the ...

A) frequency of the modulation.
B) wavelength of the audio waves.
C) amount of signal picked up by the

antenna.

D) type of filter that is used.

6. When the two metal plates on a variable

capacitor are unmeshed the ...

A) capacitance is minimum.
B) capacitance is maximum.
C) capacitance is not affected.
D) inductance is increased.

7. The process of mixing two signals to produce a

third signal is called ...

A) filtering.
B) detecting.
C) rectification.
D) heterodyning.

8. The magic wand is used to determine ...

A) whether more or less inductance is

required in a tuned circuit.

B) whether more or less capacitance is

required in a tuned circuit.

C) the gain of an RF amplifier.
D) whether the oscillator is functioning.

9. The IF frequency of your AM radio is ...

A) 1600kHz.
B) 455kHz.
C) 550kHz.
D) 910kHz.

10. The purpose of the AGC circuit is to ...

A) automatically control the frequency of

the oscillator circuit.

B) control the band width of the IF stages.
C) reduce distortion in the audio circuit.
D) maintain a constant audio level at the

detector, regardless of the strength of
the incoming signal.

Содержание AM/FM-108CK

























































Результаты поиска

Содержание AM/FM-108CK

Отзывы:

Похожие инструкции для AM/FM-108CK

Бренды по названию

Популярные бренды

Elenco Electronics AM/FM-108CK, Сборка и инструкция по эксплуатации

Результаты поиска

Содержание AM/FM-108CK

Отзывы:

Похожие инструкции для AM/FM-108CK

Бренды по названию

Популярные бренды