background image

3/

18 

 

  

  IMPORTANT SAFETY INFORMATION 

 

 

 

• 

WARNING: 

Always shut off gas supply at the shut-off valve and disconnect the quick 

disconnect 

socket from the main gas supply when the fire table is not in using. 

• 

WARNING: 

Installation 

and service must be performed by a qualified installer, service agency or 

gas supplier. 

• 

WARNING: 

Failure to follow with the safety warnings and precautions in this manual 

may result in serious bodily injury or death, a fire or an explosion causing damage to 
property. 

• 

IMPORTANT NOTICE: 

Read and understand all warnings and precautions prior to 

assembly and use your gas fire table. Improper installation, adjustment, alteration, 
service or maintenance can cause injury or property damage. 

• 

NOTE: 

The use and installation of this product must conform to local codes. In the absence of   

local code s, use the National Fuel Gas Code, ANSI Z21.97. Reference to Natural Gas and Propane 
Installation code CSAB14 9.1 or Propane Storage and Handling code B149.2. 

• 

NOTE: 

When an 

appliance is for connection to a fixed piping system, the installation must conform 

with local codes, or in the absence of local codes with the National Fuel Gas Code, ANSI 
Z223.1/NFPA 54, or International Fuel Gas Code. 

• 

Minimum clearance from unit to comb

ustible materials 72” (182.9cm) from the top; 48” (121.9 cm) 

from all sides and back. Do not locate this fire table under any overhead enclosure. 

• 

Always use this outdoor fire table on a hard, level non-combustible surface such a concrete, rock or 
stone. An asphalt or blacktop surface may not be acceptable for this purpose. Surfaces such as dirt 
and grass may prevent the unit from having proper ventilation. 

• 

This gas 

fire table and its individual shut off valve must be disconnected from the gas supply 

piping system during any pressure testing of that system at test pressures in excess of 1/2 of psi 
(3.5 kPa). The appliance must be isolated from the gas supply piping system by closing its 
individual manual shut off valve during any pressure testing of the gas supply piping system at test 
pressures equal to or less than 1/2 psi (3.5 kPa). 

• 

Keep these instructions for future reference. If you are assembling this unit for someone else, 
give this manual to him or her to read and keep for future reference. 

• 

This gas 

fire table must be used ONLY out doors in a well- ventilated space and shall NOT be 

used inside a building, garage, or any other area. 

• 

DO NOT use this outdoor gas fire table for indoor heating. Toxic carbon monoxide fumes 
can accumulate and cause asphyxiation. 

• 

NEVER leave this gas fire pit unattended when in use. 

• 

Children should be alerted to the hazards of high surface temperatures and kept at a safe 
distance while fire table is in use. 

IF YOU SMELL GAS:

 

Shut off gas supply to the fire table. 

Extinguish any open flame. 

Do not try lighting any appliance. 

Do not touch any electrical switch, do not use any phone in your building. 

Immediately call your gas supplier from a neighbor’s phone. 

If you cannot reach your gas supplier, call the fire department. 

 

WARNING   

FIRE TABLE IS FOR OUTDOOR USE ONLY 

Содержание OFM103-NG



















Отзывы: