Element4 Lucius 100 Скачать руководство пользователя страница 45

Страница: 45 / 64

MAINTENANCE

Element4 Gas Fireplaces Rev# 07082020

European

Home

.com

To see how to remove the glass from an Element4 fireplace please

visit the link below.

WWW.EUROPEANHOME.COM/RESOURCES/VIDEOS/

REMOVING AND CLEANING THE GLASS

Step 1.

Remove the three trim pieces (magnetically attached) from the

fireplace. There is no top trim on the fireplace. The trim pieces

are held firmly in place with magnets and will simply lift out. The

bottom (horizontal) trim is at the lower edge of the glass panels

and the side (vertical) trim is where the glass meets the wall.

Step 2.

Each long glass panel is held in place by two gasketed glass

clamps on the top and bottom edge and one vertical clamp on

the closed end of the fireplace. Remove the retaining bolt(s)

holding the glass clamps and then remove the clamps.

Step 3.

Securely attach the suction cup to the center of the glass and lift

the glass up into the clearance notch.

With the glass panel raised into the notch, swing the lower edge

of the glass panel out towards the room and gently lower the

glass towards the floor until it clears the fireplace.

Step 4.

Repeat Steps 2 and 3 for the other long glass panel.

Step 5.

TO REMOVE THE END GLASS, PLEASE CONTACT EUROPEAN

HOME. The end glass can also be cleaned in place once the other

glass panels have been removed.

PROPERLY PLACE, CLAMP AND SEAL THE GLASS PANEL(S)

BEFORE LIGHTING THE FIRE!

REMOVING THE GLASS

• No. 2 Phillips screwdriver (not included)

• Gloves (not included)

• 1 Suction Cup (included)

TOOLS REQUIRED

PLEASE CONTACT EUROPEAN HOME FOR MORE INFORMATION

The glass panels are held in place by 12 gasketed clamps (five on

each long glass and two on the end glass. These instructions will

show you how to remove and install the glass panel(s).

Please read these instructions completely before proceeding.

OVERVIEW

Side Trim

Bottom Trim

Figure 91

Figure 92

Figure 93

Содержание Lucius 100

































































Результаты поиска

Содержание Lucius 100

Отзывы:

Похожие инструкции для Lucius 100

Бренды по названию

Популярные бренды

Element4 Lucius 100, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Lucius 100

Отзывы:

Похожие инструкции для Lucius 100

Бренды по названию

Популярные бренды