67
violent and lose control of the tool. To facilitate cutting
and security , working with a movement from right to
left . To avoid kickback , observe the safety instructions
below effect :
a) Before starting work , inspect the work area and
remove the grass around obstacles.
b) During use, take nothing else in his hands as
handles .
c) When using the trimmer , stay focused .
d) During use, be careful not to approach too close to the
machine feet, legs or above the waist.
4 . Things to check before using the machine
a) Before commencing work, carefully look around to get
a glimpse of the in ¬ law to clear brush . Ensure that
there is no obstacle that could hinder the work . If this is
the case, remove the annoying obstacles. Check that the
area does not contain clear stones, son of iron or plant
too thick ( greater than 1 cm diameter).
b) A perimeter 15m of the user should be considered
dangerous and in which no one may enter while the
machine is running. When the work is done by two or
more persons at the same time , always check out where
other people are and maintain the correct distance
between each person.
c) Make sure no screw or nut is loosened . Check there
is no leakage, breakage , deformation or any other
problem on the machine that may affect its operation.
Particular care to ensure that there is no problem with
the blade or the blade support .
d) Never use devices twisted cut , damaged, cracked,
broken or damaged.
e) Check the clutch , making sure the cutter stops
turning when the engine is idling.
f) Check the fixing bolt of the blade and ensure that the
blade rotates smoothly and without noise.
5. Fuel supply: safe handling
Be very careful when han-dling fuel. They are flammable
and vapors are explosive. Should observe the following
points:
• Safety
a) The fuel is highly flammable, it must always be
handled with care.
b) Always refuel outdoors, away from open flame or
sparks. Do not inhale fuel fumes as they are toxic.
c) Never add fuel when the engine is running or hot.
d) Do not let petrol or oil come in contact with skin.
e) Keep the oil and gas away from eyes. In case of spills
of oil or gasoline in your eyes, immediately rinse with
clean water. If irritation persists, consult a physician
immediately.
f) Clean up any spilled fuel immediately.
• Mixing the Fuel
a) This tool uses a two-stroke engine which
requires pre-mixing gasoline and 2-cycle oil . Me-
changing of unleaded gasoline and 2-cycle engine oil in
a clean container approved for gasoline .
b) The engine is certified to operate on unleaded
gasoline intended for automotive use with an octane
rating of 90 ( [R + M] / 2) or more.
c) Do not use any mixtures prepared gas stations such
as those used in motorcycles , mopeds, etc. .
d) Use oil 2 automélangeuse time high quality air-cooled
engines . Do not use automotive oil or 2-stroke outboard
engines.
e) Mix the fuel thoroughly before each supply. Mix in
small amounts. Do not mix more fuel than will be used
within a period of 30 days. It is re ¬ controlled using 2-
cycle oil containing a fuel stabilizer.
f) Use only approved containers .
• Filling
a) Clean the area around the filler cap to prevent fuel
contamination .
b ) Loosen the fuel cap slowly to release pressure and to
keep fuel from escaping .
c) Never remove the cap of the fuel tank or add fuel
leaving the engine running . Cool the engine and
exhaust system components before refueling .
d) Fill the fuel tank carefully. Do not overfill the tank.
Avoid spilling fuel . Always stop the mo ¬ tor before
refueling . Never fill the tank of a machine while the
engine is running or hot . Move at least 5 m from the
refueling site before starting engine . Do not smoke!
e) Always replace the cap of the fuel tank and tighten it
well after refueling.
f) If fuel is spilled , do not attempt to start the engine but
move the machine away spillages before starting .
g) Never refuel in a closed room.
h) Never house tool or fuel container in a room where an
open flame such as a water heater.
Содержание DCBT52D-2SS22
Страница 84: ...84 ...
