9.1.2. Cutting narrow workpieces (Fig. 27)
Be sure
to use a push stick (3) when making
longitudinal cuts in workpieces smaller than 120
mm in width. A push block is supplied with the
saw!
Replace a worn or damaged push stick
immediately.
9.1.3. Cutting extremely narrow workpieces
(Fig. 28)
Be sure
to use a push block (a) when making
longitudinal cuts in very narrow workpieces with
a width of 30 mm and less.
The low guide face of the parallel stop is best
used in this case.
There is no push block supplied with the
saw! (Available from your specialist
dealer)Replace the push block without delay
when it becomes worn.
9.1.4. Making bevel cuts (Fig. 24/30)
Bevel cuts must always be used using the parallel
stop (7).
Set the blade (4) to the desired angle. (See 8.5.)
Set the parallel stop (7) in accordance with the
workpiece width and height (see 8.3.1)
Carry out the cut in accordance with the
workpiece width (see 9.1.1., 9.1.2 and 9.1.3.)
9.1.5. Making cross cuts (Fig. 25/31)
Cross cuts are made with the help of the drag
function.
Set the saw blade to the desired angle (see 8.5).
Use the universal stop as explained in Section
8.4.
Hold the workpiece firmly with one hand and
press it against the stop rail.
With the other hand slowly pull the saw blade on
the drag device (8) forwards through the
workpiece.
When you have finished the cut, do not allow the
saw unit to jump back into starting position on its
own but guide it back slowly by hand.
Switch off the saw again.
Do not remove the offcut until the blade has
stopped rotating.
10.Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
11. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
11.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
11.2 Maintenance
Important!
Pull out the power plug first.
Remove dust and dirt regularly from the
machine. Cleaning is best carried out with a fine
brush or a cloth.
Never use caustic agents to clean plastic parts.
Keep the saw unit drag device clean and
lubricate it in regular intervals.
11.3 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
12. Disposal and recycling
The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
E
EN
N
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
Содержание PSEm 2505P
Страница 2: ...Т а ш е в Г а л в и н г О О Д w w w t a s h e v g a l v i n g c o m ...
Страница 8: ...28 29 30 31 b M6 x 16 a a Т а ш е в Г а л в и н г О О Д w w w t a s h e v g a l v i n g c o m ...
Страница 60: ...Т а ш е в Г а л в и н г О О Д w w w t a s h e v g a l v i n g c o m ...
Страница 61: ...Т а ш е в Г а л в и н г О О Д w w w t a s h e v g a l v i n g c o m ...
