Elektra Beckum TKHS 315 (AUS), Руководство по эксплуатации, Страница: 8 / 20

8
ENGLISH
2. Fasten the rear bearing plate (66)
(with oblong hole) to the rear chip-
case guide panel
(65) (convex hole
facing inward):
−
Place guide rollers (64) with the
smaller washer from the outside
in the curved oblong holes.
−
Put hexagon head screws (63)
from the outside through the
guide roller
(64) and the holes of
the bearing plate.
−
Screw on the flange nut (67) from
the inside.
3. Install the front bearing plate (68)
likewise on the front chipcase guide
panel
(69) – fit the indicator (70) as
illustrated between the screw's head
(63) and guide roller (64) .
4. Adjust bearing plates so that the
their lower edges are parallel with
the table top.
5. The two lower cam plates serve as
stop for the bearing plates; adjust
and tighten them.
6. Affix the angle scale (71) to the front
chipcase guide panel – the two
holes in both the chipcase guide
panel and the angle scale must be
aligned as illustrated.
Motor carrier unit installation
1. Place the motor carrier unit (69) ver-
tically between the two bearing
plates.
2. Bolt motor carrier unit to the bearing
plates:
−
At front and rear, fit three each
countersunk screws
(68) from the
outside into the holes of the bear-
ing plate and the corresponding
holes in the motor carrier unit.
−
From the inside put a washer (70)
and a flange nut (71) on each
screw.
3. Align motor carrier unit to be exactly
vertical to the table top and tighten
the countersunk screws.
Bevel tilt setting device installation
1. Put on the outer clamping piece (74)
to the outside of the rear chipcase
guide panel, and the inner clamping
piece
(75) to the inside of the rear
bearing plate.
2. Secure both clamping pieces with
cap screw
(72) , four disc springs
(73) and prevailing torque-type hex-
agon nut (76) :
−
Place the prevailing torque-type
hexagon nut
(76) from the inside
into the seat provided on the
inner clamping piece
(75) .
−
Put the four disc springs (73)
with their convex sides facing
each other on the cap screw
(72) .
−
From outside, put the cap screw
through the clamping pieces and
screw into the prevailing torque-
type hexagon nut – tighten the
cap screw only so much that the
bearing plate will still move.
3. Fit the setting tube (77) at the rear
into the inner clamping piece and at
the front into the corresponding hole
of the bearing plate.
60
61
62
62
61
60
64
65
63
66
67
Item Description Qty.
68
Hex. socket counter-
sunk head screw
M6 x 16 6
69
Motor carrier unit 1
70
Washer
∅
8.4/25 6
71
Flange nut M6 6
67
68
69
63 64 70 71
70
69
71
68
Item Description Qty.
72
Hex. socket counter-
sunk head screw
M8 x 35 1
73
Cup spring 8.216 4
74
Outer clamping piece 1
75
Inner clamping piece 1
76
Hexagon nut, prevail-
ing torque-type, M8 2
77
Setting tube 1
78
Pinion shaft 1
79
Threaded rod 1
80
Setting knob 1
81
Washer 17/30 1
82
Hexagon thin nut,
M16 1
83
Washer 8.4/17 1
84
Lock lever 1
72
73
76
75
74