eLEDing
®
/ EE800W-SH series
Solar Powered LED Smart Street/Parking Lot Lighting
Lighting Profile Setup & Battery Change: open the bottom cover (Fig. 2)
Battery change: unplug the old battery and replace it with the new battery. Noted that the battery plug only fit in one way.
VR1: adjust dimming brightness (can be adjusted from 5-50% of max brightness, turn clockwise to increase brightness)
VR2: adjust sensor range (can be adjusted from 10 - 50 ft, turn counterclockwise to decrease sensitivity range)
Notes: increasing dimming brightness & sensitivity may reduce the length of illumination period, especially during winter time
Installation Guidelines
1. Securely mount the unit on the light pole or wall, adjust the light head direction and angles based on your need (Fig.4)
2. Solar Panel must be mounted in a non-obstructed position that allows at least 5-6 hours direct sunlight all year round. For most of the North
America projects, adjust the tilt of the solar panel at 25
°
- 45
°
degrees based on your actual location. If you are close to equator
’
s location, a flat
installation (light head is parallel to the ground) will be enough.
The solar panel can be pointed to east, west and south but
definitely not to north
.
For northern hemisphere installations, a south-facing position is best and visa-versa for southern hemisphere installation.
Optional AUX DC power sources can be used as back-up power source or charging enhancement device, to give the light a quick charge before
installation or during low power due to critical weather (Fig. 1).
3. Solar Panel Maintenance: Use soft, wet cloth to clean the solar panel periodically (at least once a one year) to avoid energy output reduction
resulted from accumulated dust. Clean accumulated snow ASAP during snowing season.
EE Systems Group Inc.
(Patented Technology)
Rev: 04192018
ON/OFF
AUX for:
External solar panel
USB Adaptor 12-24V, 2A
Power Bank
Fig.1
Fig.3
Fig.4
VR2: adjust sensor range
VR1: adjust dimming brightness
Select lighting
profile:
unscrew &
remove the
cover, use
jumper 2
Battery
Connect
Plug
Fig.2
Recommend
to charge 1
day before
installation,
switch in OFF
position
light
blink
once
5-min walk
test mode
5-10 sec
Motion
If
Yes
Light ON
Light OFF
No
5 min
Daytime?
Light On
Yes
Light
OFF
Light turns ON
When
nighttime
comes
Thank you for choosing eLEDing!
This product is designed to provide long lasting superior illumination by using environment-friendly Solar-Hybrid, Lithium-based energy
technologies. US, European, China and international patents granted and pending worldwide. All rights reserved. Users must read this manual
before installation, comply with local standard and regulations of construction & electrical/electronic projects, follow the safety guidelines to
prevent any possible accidents, incident and/or injuries. Consult experienced contractor/installer and electrical technicians for assistance.
Push
Switch
No
One Step Setup (Just 1 Click!)
Default
Setting
Put Jumper 2 at Close
position
SMART 2 Mode
SMART lighting profile
(Fig.2 & 3)
Dimming brightness
until dawn
Dusk to Dawn with
dimming brightness
Full brightness
After 3 hours
come to full
brightness
Recommend for areas
with busy traffic and
sufficient sunlight all
year round.
Recommend for
high-latitude, long
winter areas with
low traffic.
Motion
detected
Motion
detected
If low power
(20% left)
ON with full
brightness
Motion
Switch to
AUTO Mode
Light OFF
No
Yes
Yes
Full Charge
Back to SMART Mode
NO
Critical Reserve
(10% left)
ON with half
brightness
Motion
Light OFF
No
Yes
Intelligence Power Management (IPM) system : monitor & adjust power consumption
SMART 1 Mode
If change lighting profile
12346 Valley Blvd, #A, El Monte, CA 91732 Phone Number: 1-877-579-3889 Fax: 626-452-9194 Web: www.eleding.com/www.eesgi.com
After Full
Charge
EESGI guarantees this product to be free from defects in material &
workmanship for (1) year.
This warranty does not apply to damage from misuse or incorrect installation/
connection.
This warranty does not cover accessories, bulbs, batteries, high voltage
accidents, alterations, unauthorized use or repair, neglect, misuse, abuse,
damages or defects resulting from normal wear and tear (including chips,
fading scratches, abrasions or discoloration due to usage or sun exposure), or
failure to follow instructions for care and maintenance, fire, flood, and Acts of
God.
This warranty does not include liability for incidental or consequential
damages.
EESGI is not responsible for any damages in excess of the retail purchase
price of the product under any circumstances. The consumer is responsible
for the installation of, removal of, and reinstallation of the product.
One Year Limited Warranty
