OPERATING INSTRUCTIONS
WARNING:
Do not use this bed warmer unless it is installed to full size. Failure to follow instructions could cause
overheating and possible risk of fire or injury. Read the installation instructions above before operating.
1. After the warmer has been installed, push the on/off button to turn the control on. The control has 10 settings from “L”
to “H”. Upon the first power up the control will start at a setting of ”L” (low). Pushing on the up arrow will increase the
control to a warmer heat setting. The control automatically pre-warms the bed at full power for a period of time that is
related to the setting, no need to preheat at a high setting.
2. The control is equipped with a backlight that comes on for 10 seconds after the user turns on or adjusts the setting and
then turns off. The backlight turns off to save power and to provide an undisturbed sleep environment.
3. Be patient. It may require several minutes to warm your bed. The warmer must be covered to trap the warmth or it may
seem not to be heating. The pad may feel cool to your hand, but it will be warm when you lie on it. See 4 below.
4. The control(s) may be adjusted to regulate the warmth. Adjust the control up or down one number at a time until you find
the desired temperature setting. The control will hold that heat setting in memory after turning it off, or after the 10 hour
auto off, and will be the default setting the next time the control is turned on. The exception is if there is a power outage or
the plug is removed from the outlet, then you must reset the heat setting.
5. Do not expect to feel warmth at settings below 2 unless the room is cold.
6. Test your warmer only when it is installed, covered, and the control is set at “H”. If the warmer is not covered, heat will
escape rapidly and the warmer may not feel warm to your hand even though it is operating properly. All warmers are
thoroughly tested before being packaged. Be sure the plug makes a good connection in the outlet.
7. The control is equipped with an
automatic 10 hour shut-off
. After 10 hours of continuous use the warmer will shut off.
To turn the control back on press the on/off button.
8. The control is equipped with a safety feature that will prevent heating in an unsafe condition and will read “F” when
in that mode. If this occurs, turn control off and check the engagement of the cord to the pad. After re-engaging the
connector, turn the control back on. If “F” still appears on the control then a failure has occurred and the pad should not be
used.
Do Not
• Use bleach or dry cleaning fluids.
• Twist or wring vigorously.
• Use a wringer.
• Iron mattress pad.
• Use mothballs or sprays.
• Turn mattress pad “on” until it is completely dry.
Machine Wash
• Wash in mild soap and lukewarm water on the
delicate cycle. Do not use bleach.
• Rinse in fresh, lukewarm water.
• Spin dry.
• Gently stretch to original size, do not put through a
wringer.
Machine Dry
• Do not use commercial dryers or dryers at your
local laundromat.
• Dry warmer on delicate fabrics setting.
• Remove warmer while still damp and gently
stretch to original size.
• Air dry over parallel lines of a shower rail.
Hand Wash
• Wash in mild soapy water.
• Squeeze soapsuds through a few times.
• Rinse in fresh water.
Line Dry
• Do not use clothes pins.
• Air dry over two parallel lines. Bed warmer may
be hung over a shower rod if parallel lines are not
available.
• Gently stretch to original size.
Made & Serviced By:
ElectroWarmth Products LLC.
Box A, 513 Market Street
Danville, OH 43014
800-990-4622
WASHING INSTRUCTIONS
Do Not Dry Clean.
Dry cleaning will damage the mattress pad wiring. Wash your mattress pad, following all
instructions carefully. Be sure to disconnect the control cord before washing.
4001344
CONFORMS TO UL STD 964
CERTIFIED TO CSA STD C22.2 NO. 101
