background image

ESD

ESD

!

"

!

!

!

!

!

Kindly forward this product manual to the end user.
The user is requested to read the manual thoroughly
before operating the instrument.

#

$

Warranty Certificate

Warranty Certificate

Warranty Certificate

Warranty Certificate

Warranty Certificate

This instrument is warranted against any manu-
facturing defects for a period of twelve months
from the date of installation, or eighteen months
from the date of supply, which ever is early.

Kindly note that:
1. The warranty is limited to repairing the instru-

ment and no responsibility is taken for any
other damage resulted

2. The warranty will be void if the instrument is

opened or tampered in any way

3. The faulty instrument  has to be returned to

our factory, carriage  prepaid & duly insured.

Product Category

 :  Programmable

   Process  Controller

Model No.

:   FIT 7223

Serial number

: ________________

Date of despatch

: ________________

Authorized signatory

: ________________

Company seal

Warranty Certificate . . .

PROGRAMMABLE  PROCESS CONTROLLER

The Inside Stuff

As You Unpack

.................   2

Introduction

.................   3

Principle Of Operation

.................   4

Features

.................   4

Specifications

.................   5

Illustrations

.................   6

Operation

.................   7

Modes of Operation

.................   8

Programming Flow Chart

.................     9

Installation Procedure

.................   13

 Calibration  Procedure

.................   14

Modbus Protocol

.................   16

Important Terms

.................   19

Warranty Certificate

.................   20

20

1

Содержание FIT 7223











Отзывы: