manualshive.com logo in svg

Electrolux W5105H, Руководство по установке

Поделиться
Скачать
Electrolux W5105H Скачать руководство пользователя страница 17

Water connection

17

4 Water connection

All water intake connections to the machine should be fitted with manual shut-off valves and filters,
to facilitate installation and servicing.

Water pipes and hoses should be flushed clean before installation.

The machine shall be connected with new water hoses. Re-used water hoses must not be used.

Hoses are to be of an approved type and grade and comply with IEC 61770.

After installation hoses must hang in gentle arcs.

All connectors present on the machine must be connected. The table shows the possible connection
options, which will depend on the water types to be connected to the machine. Information is also
available on the panel above the connections.

Water type

Water connection

1

W565H, W575H

• Cold

W565H, W575H

1. Cold

2

1

W565H, W575H, W5105H, W5130H

• Cold and hot

W565H, W575H, W5105H, W5130H

1. Cold

2. Hot

2

1

3

W5180H, W5240H, W5300H

• Cold and hot

W5180H, W5240H, W5300H

1. Cold

2. Hot

3. Cold (for detergent container) /

Hot

There is also an extra water valve which can be used for hard water if soft water is connected to 1.
This valve can also be used for water re-use from tank.
If pump is used, it is only a water connection without valve.

Water pressure:

Miniumum: 50 kPa (0.5 kp/cm

2

)

Maximum: 1 MPa (10 kp/cm

2

)

Recommended: 200–600 kPa (2–6 kp/cm

2

)

Note!

If the water pressure is below the minimum value, the wash result can not be guaranteed
for certain program.

Содержание W5105H













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды