OPERATING INSTRUCTIONS
62.9692.01
Page 12
Fitting the scrapers
Operating the stirrer
Starting the stirrer:
•
Close the lid
•
Place main switch (H), where fitted, to the On position.
•
Switch on the control switch (S)
•
Set stirrer switch (RW) as required according to the follow-
ing operating programme:
Position (RW) Function
0
Stirring system switched off.
10 o'clock
Stirrer rotates continuously on same side clock-
wise.
2 o'clock
Stirrer rotates alternately right and left with a 4
second rest period and a 16 second running
period.
3 o'clock
Stirrer rotates alternately right and left with a 16
second rest period and a 16 second running
period.
The choice of programme is dependent on type of produce.
Step "left" is adequate for very fluid produce; steps "right" are
used for thick produce which is difficult to mix.
Safety measures
Always keep lid closed when operating the stirrer.
•
The stirrer remains at rest after a power failure. It can only
be restarted by actuating the stirrer switch (RW), ie. first set
to position 0 and then back to the required programme.
•
No objects (eg. mixing spoons, measuring rod, etc.) are to
be placed in the pan whilst the stirrer is running.
•
In the event of faults, blockage or the occurrence of unu-
sual noise, the stirrer switch (RW) must be placed immedi-
ately to position 0. The stirrer may not be switched on
again until the fault has been remedied.
•
If the drive motor is overloaded, the stirrer is switched off
by a thermal cut-out. Switch (RW) is to be immediately
placed to position 0. Further operation of the stirrer is only
possible when the cut-out has cooled.
•
If the drive motor is frequently overloaded and cuts out, the
produce is too stiff. Stirring can be maintained by thinning
or by removing part of the produce.
Shutting down
Place stirrer switch (RW) to position 0.
Emergency shutdown
The stirring system can be shut down by pressing the red but-
ton (N). The red button will remain depressed until is turned
clockwise. To switch on again, the stirring system switch (RW)
must be turned to position 0 and then reset to the setting of the
desired operating programme. The stirring system will recom-
mence operation after a delay of a few seconds.
Mixing when the lid is open
(only if a lid contact switch is fitted)
During normal operation, the lid limit switch automatically
switches off the mixer if the lid is opened during operation.
However, it is possible to deactivate the lid limit switch tempo-
rarily in order to observe or check the food during mixing with
the lid open or if it is necessary to add certain ingredients
evenly to the food.
Bridging the lid limit switch:
The mixer is switched on to a selected operating level. Switch
(RW).
The button (U) on the right-hand console is then pressed and
held down. After 2 seconds, the bridging of the limit switch is
activated with the lid open.
While the button remains held down, an intermittent signal is
heard and the lamp (LU) goes on and off.
Releasing the key (U) will cause the mixer to stop.
Closing the lid again will cause the mixer to recommence oper-
ation.
NB: The lid limit switch can be bridged during all the working
programs of the mixer. Please note that the mixer is subject to
interruptions in operation of between 4 and 16 seconds
dependent on program. If bridging is started during one of
these interruptions, it will be necessary to wait with bridging
until the mixer starts again. Working with utensils or reaching
into the pan is absolutely prohibited while the mixer is still
switched on (switch RW).
Removal
Push the buttom (1) and pull
simultanously the complete fixa-
tion bolt (2). Remove the
scraper (3).
Insertion
Insert the scraper (3). Push the
buttom (1) and push simultane-
ously the complete fixation bolt
(2).
Fig. 11
Fitting the scrapers
1
3
2
1
3
2
RW Stirrer switch
N
Stirrer button,
Fig. 12 Left console
LR
Q
R
LS
LU Lamp, mixer
C
U
Button, mixer
S
Fig. 13 Right console
