●
Check that the door gasket seals all around when the
door is closed and that the door moves freely
●
Move cover plate from one handle mould to the otherone
DOOR PANEL
The door panel can easily be mounted or changed. The
dimensions of the panel must be:
Height
. . . . . . . . . . . . . . . . . . . . . . . . . 722 mm
Width
. . . . . . . . . . . . . . . . . . . . . . . . . 504 mm
Thickness. . . . . . . . . . . . . . . . . . . . max 3.8 mm
●
Remove the door, see REPOSITIONING THE HINGES.
●
Remove the lower trim moulding and then withdraw the
panel by sliding it downwards.
●
Fit the new panel in place and slide it up as far as possi-
ble.
●
Fit the trim moulding back in place.
INSTALLATION
The room should have a capacity (length x width x height)
of at least 20 m
3
and have a window (which can be opened)
or a door to the outside.
It is important that the refrigerator is not subject to radiation
of heat from a stove etc.
For best performance also at high ambient temperatures
there must be a free air circulation over the cooling unit at
the rear of the refrigerator.
The refrigerator is designed for a free-standing installation
and the clearance to side walls etc., should be at least 5 cm
(2'').
LP GAS CONNECTION
The refrigerator is designed for operation on LP gas, the
pressure of which must be 28 mbar for Butane and 37 mbar
for Propane. Check that this is stated on the data plate.
The refrigerator is not designed for operation on town gas or
natural gas.
The gas installation should only be carried out by an autho-
rized gas fitter.
The gas supply pipe should be connected to the gas inlet
pipe on the right hand side of the gas control valve by
means of a suitable threaded coupling.
In making the connection to the refrigerator, a union gas
cock of an approved bottled-gas type must be incorporated
in the supply line in a position which is readily accessible to
the user. For eventual servicing purposes, the union should
be on the outlet side of the cock and the pipework should
be positioned so as not to prevent the refrigerator from
being readily withdrawn.
ELECTRICAL CONNECTION
The electrical installation must be carried out in a proper
and durable manner, taking into account all relevant regu-
lations and codes of practice. For mains voltage operation,
it is important that the circuit to and in the caravan is effec-
tively earthed.
ALL MAINS VOLTAGE WIRING IN THE CARAVAN MUST
BE INSTALLED IN ACCORDANCE WITH CURRENT
I.E.E. REGULATIONS INCLUDING THE USE OF AN
OUTLET AND COUPLER TO BS4343/- CEE17.
For connection to a 230 V electricity supply, the refrigerator
has a 3-core mains lead which is intended for connection to
a properly earthed plug and socket outlet. The socket outlet
should be fitted in the caravan in a position readily accessi-
ble to the user, within reach of the mains lead. In the United
Kingdom, the plug and socket outlet should be of the non-
reversible type.
IMPORTANT: The wires in the mains lead of this appliance
are coloured in accordance with the following code:
GREEN-AND-YELLOW = EARTH
BLUE = NEUTRAL
BROWN = LIVE
As the colours of the wires may not correspond with the
coloured markings identifying the terminals in your plug, in
the United Kingdom, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be
connected to the terminal in the plug which is marked with
the letter E or by the earth symbol
, or coloured green
or green-yellow.
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured BROWN must be connected to
the terminal which is marked with the letter L or coloured
red.
WARNING - THIS APPLIANCE MUST BE EARTHED.
In the United Kingdom, the plug or circuit to the refrige-rator
must be fitted with a fuse not greater than 5 amps. If a 13
amp.(B.S.1363) fused plug is used, it should be fitted with a
3 amp. fuse. In other countries, the fuse rating will depend
upon the voltage and local practice.
Plug the 230 V refrigerator power cord into an easily acces-
sible wall socket.
The notations in the wiring diagramme (fig. 2) are:
G. Electric thermostat
H. Heating element, 230 V
I. Switch for 230 V operation
CAUTION! CHECK THAT THE GAS SUPPLIED TO THE
REFRIGERATOR IS AT THE CORRECT PRESSURE.
SEE THE REDUCING VALVE ON THE LP GAS CON-
TAINER.
Electrical leads must be routed and secured so that
they cannot come into contact with hot or sharp parts
of the refrigerator.
8
