Cutting Height (Without Levers)
If your lawnmower has wheel hubs as illustrated
in
Fig P1
, the height of cut is adjusted by
following steps
P1-P3
.
1. Remove the wheel by turning the wheel hub in
an anticlockwise direction
(P1)
and relocate in
new hole
(P2)
turning the wheel hub in a
clockwise direction to tighten
(P3)
. Repeat for
other wheels adjusting to the same position.
Always handle the blade with care - sharp edges
could cause injury. USE GLOVES. Renew your
metal blade after 50 hours mowing or 2 years
whichever is the sooner - regardless of condition.
If the blade is cracked or damaged replace it with
a new one. Never use a blade bolt if the insulated
head is damaged cracked or missing.
Removing the Blade and Fan
1. To remove the blade bolt, hold the fan firmly and
with the spanner provided loosen the blade bolt
by turning it anti-clockwise
(R)
.
2. Remove the blade bolt, blade, and fan.
3. Inspect for damage and clean as necessary.
Fitting the Blade and Fan
1. Ensure the fan is located correctly.
(S)
2. Fit the blade to the fan with the sharp edges
pointing away from the fan.
3. Re-assemble blade bolt through blade and fan.
4. Hold the fan firmly and tighten blade bolt firmly
with a spanner. Do not over tighten.
IMPORTANT - USE GLOVES
Never use water for cleaning your lawnmower.
Do not clean with chemical, including petrol, or
solvents - some can destroy critical plastic
parts.
1. Remove grass from under the deck with a
brush.
(T)
2. Using a soft brush - remove grass clippings from
all air intakes
(U)
, the discharge chute and the
grass box.
3. Remove the blade to gain access to the fan and
clean with a soft brush.
(V)
4. Wipe over the surface of your lawnmower with a
dry cloth.
Cutting Height (With Levers)
Levers Fitted, Lowest Cut Height - (Q2,4)
Levers Fitted, Highest Cut Height - (Q3,5)
Levers Fitted, Semi Central - (Q6)
Levers Fitted, Central (Q7)
If you have levers fitted to the wheel do not
attempt to unscrew the wheel hub. Use the
levers to alter the height of cut.
1. If you have Height of Cut levers
(Figs. Q)
, the
height of cut is altered by pulling the adjustment
lever away from the location slots and moving to
the selected position
(Q1)
.
2. If your electric wheeled rotary is fitted with more
than one lever then these must be adjusted to
the same position
(Figs. Q2 - Q6)
.
Please Note : Your electric wheeled rotary may
be fitted with a mixture of cutting heights.
Cutting System
Cleaning
Caring
At the End of the Mowing Season
1. Replace blade, bolts, nuts or screws, if
necessary.
2. Clean your lawnmower thoroughly. Do not clean
with chemicals, including petrol or solvents -
some can destroy critical plastic parts.
3. Ask your local Service Centre to clean the air
filter thoroughly and carry out any service or
repairs required.
4. Make sure that the electric cable is coiled properly.
Storing your Lawnmower:
Store in a dry place
where your lawnmower is protected from damage.
The switchbox is provided with a lock-off button
to prevent accidental starting.
To Start Your Lawnmower. (L1, L2, L3)
1. Press and hold the lock off button on the
switchbox,
(L1)
then squeeze the Start/Stop lever
towards the upper handle
(L2)
.
2. Continue to squeeze the start/stop lever and
release the lock-off button
(L3)
.
To Start your Lawnmower (M1, M2, M3)
1. Connect plug to mains and switch on.
2. Tilt the handle downwards to slightly raise the
front of the lawnmower and to reduce the risk of
lawn damage whilst starting.
3. Press and hold the lock-off button
(M1)
on the
switchbox, then squeeze one of the Start/Stop
levers towards the upper handle
(M2)
.
4. Continue to squeeze the start/stop lever towards the
upper handle and release the lock-off button
(M3)
.
5. Lower the lawnmower to its proper operating
position and commence mowing.
To Stop Your Lawnmower.
1. Release the pressure of the Start/Stop lever.
NOTE (M1, M2, M3)
There are two start/stop levers fitted. Either one
can be used for starting the lawnmower.
IMPORTANT
Do not use the start/stop levers intermittently
Starting and Stopping
How to Mow
1. Start mowing the edge of the lawn nearest to the
power point so that the cable is laid out on the
lawn you have already cut
(N)
.
2. Mow twice a week in the growing season, your lawn
will suffer if more that one third of its length is cut at
one time and this may also result in poor collection.
Please Note
Do not overload your Lawnmower
When mowing in long thick grass a first cut with the
cutting height adjusted to its highest setting, see
Cutting Height
, will help reduce motor overload and
will help prevent damage to your lawnmower.
ENGLISH - 3
