3. Refit the HEPA filter assembly into the cleaner.
4. Fit the filter grille into position and press down
to lock into place.
Replacement HEPA filter Part Number
???????
Replacement of the washable HEPA exhaust
filter ( Z1570 )
It is recommended that this washable HEPA filter is
cleaned when visibly soiled Prior to washing with
the top of the filter facing, tap the filter on a flat
surface, this will release any heavy dust particles.
Wash the filter from the underside running tap
water over the complete area of the filter material.
Do not touch the filter material when wet. Shake out
the excess water prior to leaving for drying.
1. Release the catch at the rear of the filter
grille and lift it off the cleaner. To remove the
washable HEPA filter.
2. Remove the washable HEPA filter assembly. and
insert a new one if required other wise the filter
can be cleaned. Ensuring it is completely dry
before fitting it back into the cleaner.
3. Refit the washable HEPA filter assembly into
the cleaner.
Troubleshooting and customer information
7.
8.
Trouble Shooting
Power
The vacuum cleaner does not start.
1. Check that the cable is connected to the mains.
2. Check that the plug and cable are not damaged.
3. Check for a blown fuse.
The Vacuum Cleaner stops
1. Check whether the dust bag is full, if so, replace
it with a new one.
2. Is the nozzle, tube or hose blocked?
3. Are the filters blocked?
Blockages, full dust bags, and dirty filters can result
in the machine switching off in operation due to
the restriction of air flow causing the activation of
the thermal overload. If this does occur, switch off
at both the cleaner and at the mains and remove
the plug.
Allow the cleaner to cool for 20 – 30 minutes, in
this time check the hose, tubes and floor nozzle for
blockages.
( a ) To check for a hose blockage pass a small
coin through it, on finding the blockage, remove
it by pressing the hose to dislodge and loosen the
obstruction. How ever be careful in the case it has
been caused by glass or needles caught inside the
hose at the point of the blockage.
( b ) By passing a hard flexible tube through the
hose from the handle end the obstruction can also
be dislodged and removed.
If the obstruction cannot be removed please
consult the service provides listing supplied with
the cleaner for your nearest Electrolux authorized
Service Provider.
The clearing of a blocked hose is not covered by
warranty.
Water has entered the vacuum cleaner.
It will be necessary to replace the motor by an
authorised Electrolux service provider. Damage to
the motor caused by the penetration of water is not
covered by the warranty.
Customer Information
Should you require service or consumable spares for
your Electrolux cleaner, please consult the service
providers listing enclosed with this cleaner, for your
nearest Electrolux authorised service provider or
contact the customer service help line noted in the
booklet enclosed with this product.
New filters and dust bags can be obtained from your
Electrolux authorized service provider. Please specify
model type when ordering spares.
SAVE THESE INSTRUCTIONS
For repairs or accessories.
GUARANTEE / WARRANTY AND SERVICE
PROVIDERS BOOKLET
In reference to the warranty conditions, service,
spare parts and for your nearest service providers
information, please consult the booklet
enclosed with this product.
Electrolux
Features of the vacuum cleaner and accessories
are protected abroad by registered patents of
Registered Designs.
The appliance conforms with the requirements of
the amended E.E.C, directive No 89/336 EEC relating
to electromagnetic compatibility (EMC) CE.
The Electrolux group may introduce modifications
to their product from time to time, and
consequently the details given in this booklet are
subject to alteration without notice.
4. Fit the filter grille into position and press down
to lock into place.
Replacement washable HEPA filter Part
Number ???????
CLEANING THE HOSE AND NOZZLE
The vacuum cleaner stops automatically if the
nozzle tube or hose becomes blocked, or the filter
and dust bag are blocked. Disconnect from the
mains and allow to cool down for approximately 20
– 30 minutes.
Clear what ever is causing the blockage and /
replace dirty filters or the full dust bag. Then start
the vacuum cleaner.
Tubes and hose
1. Use a flexible hose or similar item to clear the
tubes and hose.
2. It is sometimes possible to clear the hose by
“massaging” it. However, be careful in case the
obstruction has been caused by glass or
needles caught inside the hose.
Note: The warranty does not cover any damage to
hoses caused by cleaning them.
Cleaning the floor nozzle
3. To avoid reduction in suction power, frequently
clean the dual purpose floor nozzle. The easiest
way to clean it is by using the hose bent end.
MAINTENANCE
