background image

33

Normal Operating Sounds

Understanding the 

sounds you may hear

Your new, high-efficiency refrigerator 

may introduce unfamiliar sounds. These 

sounds normally indicate your refrigerator 

is operating correctly. Some surfaces on 

floors, walls, and kitchen cabinets may 

make these sounds more noticeable.
The following is a list of major components 

in your refrigerator and the sounds they 

can cause:
 

A Evaporator

 Refrigerant through the 

evaporator may create a boiling or 

gurgling sound.

 

B  Evaporator fan

 You may hear air 

being forced through the refrigerator 

by the evaporator fan.

 

C  Defrost heater

 During defrost 

cycles, water dripping onto the 

defrost heater may cause a hissing 

or sizzling sound. After defrosting, a 

popping sound may occur.

 

D  Automatic ice maker

 When ice 

has been produced, you will hear 

ice cubes falling into the ice bin. Ice 

maker fan, water valve activation, 

and refrigerant gas fluid may create 

sounds from its operation.

 

E  Electronic control & automatic 

defrost control

 These parts can 

produce a snapping or clicking sound 

when turning the cooling system on 

and off.

 

F  Condenser fan

 You may hear air 

being forced through the condenser.

 

G Compressor

 Modern, high-efficiency 

compressors run much faster than 

older models. The compressor may 

have a high-pitched hum or pulsating 

sound.

 

H  Water valve

 Makes a buzzing sound 

each time it opens to fill the ice 

maker.

 

I  Drain pan (not removable)

 You 

may hear water dripping into the 

drain pan during the defrost cycle.

 

J Condenser

 May create minimal 

sounds from forced air.

 

K  Motorized Custom Temp

TM

 

drawer damper

 May produce a light 

humming during operation.

NOTE

During automatic defrost cycle, a red 

glow in the back wall vents of your 

freezer compartment is normal.

NOTE

Energy efficient foam in your refrigerator 

is not a sound insulator.

 

L  Ice dispensing paddle

 When 

dispensing ice, you will hear a 

snapping, clicking, or popping sound 

when the solenoid opens and closes 

the ice chute.

 

M  Motorized damper

 May produce a 

light humming during operation.

 

N  Custom Temp

TM

 drawer fan

 Turns 

off when door opens or Custom 

Temp

TM

 drawer is turned off.

Содержание ICON E23BC69SPS3












































Отзывы: