manualshive.com logo in svg

Electrolux HIC, Руководство по обслуживанию, Страница: 21 / 25

Поделиться
Скачать
Electrolux HIC Скачать руководство пользователя страница 21

- 21 -

DGN-TDS-N 11.03 U. H. / A. B. © Electrolux

599 512 232

EN

 

d. 

4.12 Demo mode / Self test (Service mode) / Alarm Menu

To enter the self-test/Demo mode, the following sequence of buttons must be pressed:

1.

Hob is off. Press main switch continuously until display is going off (without beep).

2.

Press the “+” and “ -” buttons of the front zones together (->short beep) for about 3 seconds
(-> again short beep)

3.

Press the timer selection key

4.

The display shows a „d“ for demo mode.
If you press the timer select key again you switch to “S” for Service mode,
another press gets you to “E” the alarm menu. (Test all LEDs / Displays for 10 sec.)

5.

By pressing the button “+” of a cooking zone you activate the menu. For example, status like
above shown in the graphic – hob is in demo mode, press ‘+’ key of zone to deactivate the
demo mode.

Demo Mode:
If demo mode is activated the display with the „d“ shows additionally a dot.
After selecting the demo mode, the electronic goes to off. Now it can be used like usual but only
without heater activation. The deactivation of the demo mode is done in the same procedure as
activating. After deactivating the demo mode the electronic must go off. Now the hob can be used in
normal mode.

Alarm Mode “E”
The last 5 stored alarm codes are displayed like an actual alarm, each for 5 sec., starting with the
oldest to the newest . The alarms are checked for all hob controllers. They are displayed like nor-
mal occurred alarm.

Step 1

Step 2

Step 3

Содержание HIC


























Отзывы:

Нет отзывов