23
ignition port
slots
orifice port
Fig. 1 - Cooktop burner head
CARE & CLEANING
Routinely clean the cooktop. Wipe with a clean, damp cloth
and wipe dry to avoid scratches. Keeping the surface burner
head ports and slots clean will prevent improper ignition and an
uneven flame. See the following sections for more instructions.
Cleaning the cooktop and surface burners
CAUTION
To clean recessed and contoured areas of cooktop
If a spill occurs on or in the recessed or contoured areas, blot up
spill with an absorbent cloth. Rinse with a clean, damp cloth and
wipe dry.
Always
keep the surface burner caps in place whenever
a surface burner is in use.
When replacing the burner caps, be sure the
burner
caps
are seated firmly on top of the burner heads.
The surface burner heads are secured to the cooktop and
must be cleaned in place on the cooktop.
For proper flow of gas and ignition of burners —
DO NOT allow spills, food, cleaning agents or
any other material to enter the gas orifice holder
opening.
IMPORTANT
Replacing oven light
The light bulb is located at the rear of the oven and is covered
with a glass shield held by a wire holder. The glass shield must
be in place whenever the oven is in use.
To replace the oven light bulb:
1. Turn electrical power off at the main source or unplug the
range.
2. Press wire holder to one side to release the glass shield that
covers the light bulb.
3. Replace bulb with a new 40 watt appliance bulb.
4. Replace glass shield over bulb and snap wire holder back
into place.
5. Turn power back on again at the main source (or plug the
appliance back in).
6. The clock will then need to be reset. To reset, see “Setting
the clock” in this Use & Care Guide.
Be sure the range is unplugged and all parts are COOL
before replacing oven light. Wear a leather-faced glove
for protection against possible broken glass.
CAUTION
To clean the burner head ignition ports
Each burner head has a small ignition port located as illustrated.
Should you experience ignition problems it may be that this port
hole is partially blocked with soil. With the burner head in place,
use a small wire gauge needle or the end of a paper clip to clear
the ignition port (See Fig. 1 - center burner not shown).
To clean burner caps
• Remove caps from burner heads after they have cooled.
• Clean heavy soils with a plastic scrubbing pad and absorbent
cloth.
• Thoroughly dry burner caps immediately following cleaning
including the bottom and inside of cap.
• Do not use abrasive cleaners. They can scratch porcelain.
• Do not clean burner caps in the dishwasher.
• Do not operate surface burners without burner caps properly in
place. See
IMPORTANT
notes below.
To clean burner grates
• Clean when the grates are cool.
• Use nonabrasive plastic scrubbing pad and mild abrasive
cleanser.
• Food soils containing acids may affect the finish. Clean
immediately after the grates are cool.
• Thoroughly dry grates immediately following cleaning.
To clean the surface burner heads
For proper gas flow it may be necessary to clean the burner head
and slots. To clean, first use a clean DAMP cloth to soak up any
spills. Remove any food from between the burner slots using a
small nonabrasive brush like a toothbrush and afterwards wipe
up using a damp cloth. For stubborn soils located in the slots,
use a small-gauge wire or needle to clean.
Any spill on or around the electrode must be carefully cleaned.
Take care not to hit the electrode with any thing hard or it could
be damaged.
To avoid possible burns
DO NOT
attempt any of the
cleaning instructions provided below before turning OFF
all of the surface burners and allow them to cool.
Any additions, changes or conversions required in order
for this appliance to satisfactorily meet the application
needs must be made by an authorized qualified Agency.
Содержание Frigidaire FGEF3035RFA
Страница 28: ...This page is left blank intentionally ...