Electrolux FMV156DBE Скачать руководство пользователя страница 33

Страница: 33 / 48

FMV156DBE

FMV156DSE

FMV156DQE

FMV156DCF

.  Disconnect the power supply cord.
2.  Open the door and block it open.
3.  To  discharge  the  high  voltage  capacitor,  wait  for  60

seconds.

4. Remove the one () screw holding the base cover to the

oven cavity back plate.

5. Remove the three (3) screws holding the base cover to

the oven cavity front face plate.

6. Open the base cover.
7. Release the two hood lamp sockets from the base

cover.

8. Remove the base cover from the oven cavity by pulling

down and moving to the left slightly.

the terminal hole of the oven lamp socket with the small
flat type screw driver.

9. Now, the oven lamp socket is free.

TURNTABLE MOTOR AND FOOD LAMP SOCKETS REMOVAL

TURNTABLE MOTOR
9. Disconnect the wire leads from the turntable motor.
0.

Remove one () screw holding turntable motor to

the oven cavity.

Now the turntable motor is free.

HOOD LAMP SOCKET
9. Screw the hood lamp off from the lamp socket.
0. Disconnect the wire leads from the lamp socket by pushing

the terminal hole of the lamp socket with the small flat
type screw driver.

. Now, the lamp socket is free.

. Disconnect the power supply cord, remove the oven from

the wall and remove the outer case. (Refer to procedure
of "REMOVAL OF OVEN FROM WALL" and "OUTER
CASE REMOVAL".). And proceed as follows.

2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60

seconds.

4. Remove the three (3) screws holding the hood intake duct

R to the oven cavity top plate, the oven cavity front flange
and the fan duct. And remove the hood intake duct R.

5. Turn the lamp socket and release it from the magnetron

duct.

6. Screw the oven lamp off from the lamp socket.
7. Now, the oven lamp is free.
8. Pull the wire leads from the oven lamp socket by pushing

OVEN LAMP AND LAMP SOCKET REMOVAL

POSITIVE LOCK

CONNECTOR (NO-CASE TYPE) REMOVAL

. Disconnect the power supply cord and remove the oven

from wall and remove outer case. (Refer to procedure
of "Removal of Oven from Wall" and "Outer case
Removal")

2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60

seconds.

4. Push the lever of positive lock

connector.

5. Pull down on the positive lock

connector.

CAUTION: WHEN CONNECTING THE POSITIVE LOCK

CONNECTORS TO THE TERMINALS, INSTALL
THE POSITIVE LOCK

SO THAT THE LEVER

FACES YOU.

Positive lock

connector

Oven lamp

socket

Terminal

Wire lead

Terminal hole

Flat type small

screw driver

2. Open the door and block it open.
3. To discharge the high voltage capacitor, wait for 60

seconds.

4. Remove three (3) screws holding the hood exhaust louver

to oven cavity front face plate.

5. Remove the hood exhaust louver from the oven by

pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL")

6. Remove one () screw holding the control panel to the

oven cavity front face plate.

CONTROL PANEL ASSEMBLY, CONTROL UNIT AND KEY UNIT REMOVAL

. Disconnect the power supply cord.

7. Release the control panel from the oven cavity front face

plate by lifting it up.

8. Disconnect the wire leads from the relays RY and

RY2.

9. Disconnect the connectors CN-A, CN-C and CN-E from

the control unit.

0. Remove the control panel assembly from the oven.
. Now, the control panel assembly is free.
2. Disconnect the connector CN-G from the control unit.
3. Remove two (2) screws holding the power unit to the key

Terminal

Push

Pull down

Lever

Positive lock¨

connector

Содержание FMV156DBE

















































Результаты поиска

Содержание FMV156DBE

Отзывы:

Похожие инструкции для FMV156DBE

Бренды по названию

Популярные бренды

Electrolux FMV156DBE, Руководство по обслуживанию

Результаты поиска

Содержание FMV156DBE

Отзывы:

Похожие инструкции для FMV156DBE

Бренды по названию

Популярные бренды