Electrolux EWW1042R7WB, Руководство пользователя, Страница: 18 / 52

18 www.electrolux.com
●
●
●
●
The drying time can vary according to :
the final spin speed;
dryness level (Extra Dry or Cupboard Dry or
Iron Dry);
the type of laundry;
the size of load.
Duration of the drying cycle
After drying fluffy fabrics, such as new towels,
it is advisable to perform a Rinse program to
ensure that any residue that may remain in the
tub is completely removed and does not stick
to garments dried afterwards. After each drying
cycle, clean the drain pump filter. Please refer
to care and cleaning in section 11 “CARE AND
CLEANING”.
Fibre residue
To deactivate the function, press and
hold “Prewash” touchpad about
2 seconds until the display shows the
icon “ ”.
Save Favourite ( ) Program
3.5 Settings
This setting permits you to either enable
or disable the buzzer at the end of the
program. As an example, you might wish
to disable this buzzer when you start a
wash when going to bed, so that when the
wash finished approximately 1 hour later,
it will not disturb you through the night.
Enabling/Disabling End-Of-Wash
Buzzer
Program settings that are frequently used can
be saved (e.g. Cotton, 60°C, 1200 rpm, with
Prewash and Hygienic Care).
To program/re-program Favourite with your
own selections and save them, proceed as
follows:
1. Put machine in Stand-By mode.
2. Select your desired program settings.
●
●
Additional drying
To prevent the formation of creases or
shrinking of fabrics, avoid excessive
drying.
WARNING!
Should the laundry still be too wet at the end of
the program, set another short drying cycle.
The final part of a washer- dryer cycle occurs
without heat (cool down cycle). This ensures
the laundry will be left at a low temperature.
Child Safety Lock ( ) Option
Your appliance is provided with CHILD
SAFETY LOCK which permits you to
leave the appliance unsupervised with
the door closed without having to worry
that children might be injured by or cause
damage to the appliance.
Set this option after pressing the
Start/Pause touchpad.
To activate the function, press and
hold “Prewash” touchpad about
2 seconds until the display shows the
icon “ ”.
To set “Child Lock” option:
This function remains enabled
even after the appliance is
switched off.
The touchpads are locked
(except for the On/Off button).
●
●
If you press any touchpad while
Child Lock is activated, the icon
“ ” will flash on display
3 times along with buzzer sound.
App Program cycle cannot be saved
as a Favourite on the appliance.
To recall the favourite wash program,
turn selector knob to “Favourite ”
program. You will get acknowledgement
on the screen when the Favourite
program is loaded.
3. To save favourite program, press and hold
“Hygienic Care ” touchpad about 2
seconds and you will hear “Bip, Bip” sound
and “Favourite” LED is flashing.
ENGLISH 19
BEFORE FIRST USE 4.
Ensure that the electrical and water
connections comply with the
installation instructions.
Put 2 litres of water in the detergent
compartment for washing phase. This
activates the drain system.
1.
2.
3. Select a Cottons cycle at 90 °C,
without any laundry in the machine, to
remove any manufacturing residue
from the drum and tub then start the
machine.
During installation or before first use
you may observe some water in the
machine. This is a residual water left in
the machine after a full functional test
in the factory to ensure the machine is
delivered to customers in perfect
working order and is no cause for
concern.
NOTE
3.6 Start/Pause ( ) and
Add Clothes ( ) Touchpad
Error warning beeps such as critical
faults are not disabled.
This touchpad has 2 functions:
To disable the buzzer sound, press
“SensorWash ( )” and “Hygienic
Care ( )” touchpads at the same
time about 3 seconds, the icon “ ”
will show on display along with buzzer
sound.
To return to default configuration
press these 2 touchpads at the same
time about 3 seconds, the icon “ ”
will show on display along with buzzer
sound.
●
●
Start/Pause ( ) 1.
To interrupt a program which is running,
press this touchpad to pause the machine,
the Start/Pause pilot light flashes.
If you have selected a “Delay Start”
option, the countdown will begin and
will be shown on the display.
After you have selected the desired
program and options, press this
touchpad to start the machine. The
Start/Pause pilot light will stop flashing
and remain lit until the water level is
above the bottom edge of the door
then pilot light goes OFF.
To restart the program from the point at
which it was interrupted, press this
touchpad again, the Start/Pause pilot
light will stop flashing.
Add Clothes ( ) 2.
To add clothes:
Pressing the “Start/Pause”
touchpad to pause the program.
You can only add clothes when
the icon “ ” shown on the
display.
1.
Wait for the machine to come
to a complete stop before opening
the door (wait for door lock “ ”
icon to turn off).
2.
Resume the program by pressing
“Start/Pause” touchpad again.
4.
Add clothing and close the door. 3.