5
•
Reversible
tempered
double/triple
pane
smoked glass door protects your wine from
UV light and creates an attractive display with
few condensation and low noise.
•
Black coated matte steel outer frame and
black plastic interior liner offer lifetime
performance and stability. The black liner
prevents excessive light from damaging the
maturity process.
•
Optional stainless steel-framed glass door
with stainless steel handle.
•
Optional
roll-out
and
adjustable
solid
varnished beech shelves allow for maximum
convenience and flexibility to accommodate
various size bottles.
•
Environmentally
friendly
refrigerant
and
foaming insulation gas.
•
Optional security lock system with keys.
•
Optional humidity control system (Humidity
Box).
•
Optional active charcoal air filter.
INSTALLATION
BEFORE USING YOUR APPLIANCE
•
Remove all exterior and interior packing.
Clean the interior surface with lukewarm water
using a soft cloth. The unit may have residual
odors at first, they will disappear as the unit
cools.
•
Before connecting the appliance to the power
source, let it stand upright for at least 24
hours. This will reduce the possibility of a
malfunction in the cooling system caused by
handling during transportation. During this
time we recommend that you leave the door
open to clear any residual odors.
•
The door on this appliance can be opened
from either the left or the right side. The unit is
delivered with the door opening on the left
side. Should you wish to open the door from
the right, follow the instructions ‘Reversing the
door hinge’.
•
Install the handle on the door if necessary.
INSTALLATION OF YOUR APPLIANCE
•
The appliances are designed to be built-in or
recessed or free standing installation.
•
WARNING
: Do not store or install the
appliance outdoors. The unit is for indoor use
only.
•
WARNING
: Do no install the appliance in the
laundry
.
Avoid locating the unit in damp areas.
•
Place your appliance on a floor that is strong
enough to support it when it is fully loaded. To
level your unit, adjust the front leveling leg at the
bottom of the unit.
•
For freestanding installation, 100mm of space
between the back and sides of the unit are
suggested, which allows the proper air
circulation to cool the compressor and
condenser for energy saving. Even for built-in
installation, it is a must to keep 5mm space on
each side and at the top to ensure proper
service access and ventilation. Take care that
the air vent at the front of the appliance must
never be covered or blocked in any way.
•
Locate the unit away from direct sunlight and
sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and
heat
sources
may
increase
electrical
consumption.
Extreme
cold
ambient
temperatures may also cause the unit not to
perform properly.
•
Plug the unit into an exclusive, easily accessible
plug socket. Any questions concerning power
and/or earthing should be directed towards a
qualified electrician or an authorized products
service centre.
•
The appliance must be installed to all electrical,
plumbing, water and drain connections in
accordance with state and local codes.
•
IMPORTANT: HIGH HUMIDITY CLIMATE.
During
periods
of
high
humidity,
some
condensation may appear on outside surfaces of
glass door. This condensation will disappear
when humidity levels drop. For prevention, it is
advisable to install the appliance with sufficient
ventilation in a dry and/or an air-conditioned
place.
BUILT-UNDER INSTRUCTIONS
Make sure your installation does not block the front
ventilation grille.
If the unit is installed for fitting
kitchen plinth, make sure that the ventilation gaps in
the plinth are at least 300 square centimeters and
remove the ventilation grilles, so that warm air can
disperse unhindered. Otherwise the appliance has
to work harder, resulting in an increase in electricity
consumption.
NOTE:
When pushing the appliance into the niche,
make sure that the mains cable does not get
trapped.
NOTE: The appliance must be positioned so
that the plug is accessible.