Before using your dishwasher for the first time:
1. Ensure that the electrical and water connections comply
with the installation instructions
2. Remove all packaging from inside the appliance
3. Set the water softener. No need to set the water softener
in Australia except in hard water areas of South Australia
and Western Australia.
4. Pour 1 litre of water inside the salt container and then fill
with dishwasher salt. ONLY required in hard water areas.
5. Fill the rinse aid dispenser
Note:
If you want to use the "3 in 1" detergent tablets, read
carefully the informations given in "Different Kinds of
Detergents".
The water softener
The dishwasher is equipped with a water softener designed to
remove minerals and salts from the water supply, which would
have a detrimental or adverse effect on the operation of the
appliance.
The higher the content of these minerals and salts, the harder
your water is.
Water hardness is measured in equivalent scales ppm (Parts
Per Million) and mmol/l (millimol per litre - international unit for
the hardness of water).
The softener should be adjusted according to the hardness of
the water in your area. Your local Water Authority can advise
you on the hardness of the water in your area.
The water softener must be set in both ways: manually, using
the water hardness switch and electronically, using the function
buttons on the control panel.
a) Setting manually
1. Open the dishwasher door.
2. Remove the lower basket
from the dishwasher.
3. Turn the water hardness
dial to position 1 or 2 (see
table).
4. Replace the lower
basket.
The dishwasher is factory set
at position 2.
b) Setting electronically
(The dishwasher must be switched off before starting this
procedure)
The dishwasher is factory set at level 5.
1. Press the On/Off button. All programme selection buttons
indicator lights will illuminate (setting mode).
If only one programme selection button indicator light is
illuminated, this means that a washing programme is set.
The programme must be cancelled: press simultaneously
the function buttons 2 and 3 for about 2 seconds, the
indicator light of the set programme button starts flashing
for about 2 seconds.
After about 2 seconds the indicator lights of all the
programme selection buttons will illuminate indicating
that the set programme has been cancelled and that the
machine is now in setting mode.
2. Press simultaneously function buttons 2 and 3, until the
indicator lights of the function buttons 1, 2 and 3 start
flashing.
3. Press function button 1, the indicator lights of function
buttons 2 and 3 turn off while the indicator light of the
button 1 goes on flashing, at the same time the End
indicator light illuminates, along with a
sequence of audible signals.
The current level is indicated by the number of flashes of
the End indicator light and of audible signals heard.
Example:
5 flashes, 5 audible signals, pause, 5 flashes, 5 audible
signals, pause, etc... = level 5.
4. To change the level, press function button 1. Each time the
button is pressed the level changes. (For the selection of
the new level see the chart).
Examples:
if the current level is 5, by pressing function button 1 once,
level 6 is selected.
if the current level is 10, by pressing function button 1 once,
level 1 is selected.
5. To memorise the operation, switch off the dishwasher by
pressing the On/Off button or wait about 60 seconds after
which the dishwasher will automatically return to setting
mode.
Prior to Using for the First Time
6
ppm
mmol/l
manually
electronically
9.0 - 12.5
7.6 - 8.9
6.5 - 7.5
5.1 - 6.4
4.0 - 5.0
3.3 - 3.9
2.6 - 3.2
1.9 - 2.5
0.7 - 1.8
< 0.7
900 - 1250
760 - 899
650 - 759
510 - 649
400 - 509
330 - 399
260 - 329
190 - 259
70 - 189
< 70
2
2
2
2
2
2
1
1
1
1
level 10
level 9
level 8
level 7
level 6
level 5
level 4
level 3
level 2
level 1
yes
yes
yes
yes
yes
yes
yes
yes
yes
no
10
9
8
7
6
5
4
3
2
1
Water hardness
Adjusting the water
hardness setting
Use
of salt
Number of flashes of the
"End" indicator light
and of audible signals
Содержание ESL4143
Страница 1: ...USE CARE MANUAL ESL 4143 ...
