manualshive.com logo in svg

Electrolux EMS2685, Руководство по обслуживанию

Поделиться
Скачать
Electrolux EMS2685 Скачать руководство пользователя страница 31

SOI  03.06  FV 

31/38 

599 36 78-45 

 

 

COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE

 

 

OVEN LAMP REMOVAL

 

 

 
 
1. CARRY OUT 3D CHECKS. 
2. Disconnect the wire lead from the oven lamp 
3. Lift up the oven lamp from the clips of the air 
 intake 

duct. 

4. Now, the oven lamp is free.

 

 

 

POWER SUPPLY CORD REPLACEMENT

 

 

Removal 

1. CARRY OUT 3D CHECKS. 
2. Remove the one (1) screw holding the 
  green/yellow wire to the cavity back plate. 
3. Disconnect the leads of the power supply cord 
  from the noise filter, referring to the Figure  
 C-4(a). 
4. Release the power supply cord from the rear 
 cabinet. 
5. Now the power supply cord is free.

 

 

 

Re-install 

1. Insert the moulding cord stopper of power supply cord 
  into the square hole of the power angle, referring 
  to the Figure C-4(b).  
2. Install the earth wire lead of power supply cord to the 
  oven cavity with one (1) screw and ensure that this 
 screw 

is 

tight. 

3.  Connect the brown and blue wire leads of power 
  supply cord to the noise filter correctly, referring to the 
 Pictorial 

Diagram.C-4(a). 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure C-4 (a) Replacement of Power Supply Cord 

Figure C-4 (b). Installation of Power Supply Cord

 

 

GRILL HEATING ELEMENT REMOVAL

 

 

1. CARRY OUT 3D CHECKS. 
2. Remove the one (1) screw holding the exhaust 
  duct to the oven cavity. 
3. Remove the exhaust duct from the oven cavity. 
4. Remove the two (2) screws holding the two (2) 
  terminals of main wire harness to the grill 
 heating 

element. 

 

5. Remove the two (2) screws holding the two (2) grill 
  heater angles to the top of the oven cavity.  
6. Remove the two (2) grill heater angles from the oven 
 cavity. 
7.  Remove the grill heating element from  the top of the 
 oven 

cavity. 

8.  Now the grill heating element is free. 

 

 

 

 

Socket

Bulb

 

Lock

Oven lamp

 

Noise filter

 

Power supply cord

Green / Yellow 

Blue Wire

 

Brown Wire

 

Wire

 

Screw

 

Oven cavity back plate

 

POWER  
SUPPLY CORD

 

OVEN CAVITY 
BACK PLATE

 

SQUARE HOLE

 

Содержание EMS2685







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды