background image

8

5. CONTROL PANEL 

1

1

Display : Cooking time, power level, indicators and

present time are displayed.

MW : When blinking, the oven is operating in
MICROWAVE COOK.
Grill : When blinking, the oven is operating in GRILL.
Combi : When blinking, the oven is operating in COMBI.
Defrost Weight : When blinking, the oven is operating in
WEIGHT DEFROST.
Time : When blinking, the oven is operating in TIME
DEFROST.
Auto-cook : When blinking, the oven is operating AUTO
COOK.
Lock : When lighting, the oven is CHILD LOCK.
Con-vection : When blinking, the oven is operating in
CONVECTION.
g : When blinking, the oven is operating in weight input
mode.
Barbecue : When blinking, the oven is operating in
barbecue. (KOC-9N7T7SA2 only)

2

2

Auto cook : Used to cook or reheat.

3

3

Combi : Used to select combi.

4

4

Weight Defrost : Press to select the weight defrosting

cooking. (KOC-9N4T7S/9N4T7S24/9N5T7S/9N5T7R/
9N5T7S21/9N7T7S/9N7T7S21 only)
Auto Defrost : Press to select the auto defrosting
cooking. (KOC-9N7T7SA2 only)

5

5

Grill : Used to select grill.

6

6

MW : Used to set power level of micro wave.

7

7

Time Defrost : Press to select the time defrosting

cooking. (KOC-9N4T7S/9N4T7S24/9N5T7S/9N5T7R/
9N5T7S21/9N7T7S/9N7T7S21 only)
Barbecue : Press to select the barbecue cooking.
(KOC-9N7T7SA2 only)

8

8

Convection : Used to select convection and selected

temp.

9

9

Clock : Used to set clock.

0

0

Dial knob : Used to set time, weight and quantity.

q

q

START/SPEEDY COOK : Used to start a programmed,

also for speedy start(each press adds 30 seconds
microwave cooking time).

w

w

STOP/CLEAR : Used to stop the oven operation or to

delete the cooking data.

Содержание EMC3065X





























Отзывы: