background image

42

Solutions to Common Problems

Concern Potential Cause

Common Solution

Water/Moisture/Frost Inside Refrigerator

Moisture 

collects on 

inside of 

refrigerator 

walls.

•  Weather is hot and humid. 

•  Flipper mullion

•  The rate of frost buildup and internal 

sweating increases.

•  Adjust flipper mullion. (See “To adjust 

the flipper mullion” in the Installaion 

section.)

Water 

collects on 

bottom side 

of drawer 

cover.

•  Vegetables contain and 

give off moisture.

•  It is not unusual to have moisture on 

the bottom side of the cover.

•  Move humidity control (some models) 

to lower setting.

Water 

collects in 

bottom of 

drawer.

•  Washed vegetables and 

fruit drain while in the 

drawer.

•  Dry items before putting them in the 

drawer. Water collecting in bottom of 

drawer is normal.

Water/Moisture/Frost Outside Refrigerator

Moisture 

collects on 

outside of 

refrigerator 

or between 

doors.

•  Weather is humid.

•  This is normal in humid weather. 

When humidity is lower, the moisture 

should disappear.

Food in Fresh Food Compartment

Food is 

freezing.

•  Temperature setting is too 

low.

•  Temperature sensor is 

covered by food (right side 

of fresh food area).

•  Food is covering the air 

ports.

•  Move the setting to a higher degree. 

•  Allow space for air flow to the sensor. 

 

•  Allow space between the air ports 

and the food.

Содержание EI23BC82SS












































Отзывы: