background image

9

Injectors replacement

• Remove the pan supports.
• Remove the burner's caps and crowns.
• With a socket spanner 7 unscrew and remove the

injectors (Fig. 7), and replace them with the ones
required for the type of gas in use (see Table "

Injectors

").

• Reassemble the parts, following the same procedure

backwards.

• Replace the rating label (placed near the gas supply

pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.

Should the feeding gas pressure be different or variable
compared with the required pressure, an appropriate
pressure adjuster must be fitted on the gas supply pipe,
in compliance with the rules in force.

Fig. 7

Adjustment of minimum level

To adjust the minimum level of the burners, proceed as
follows:
• Light the burner.
• Turn the knob on the minimum position.
• Remove the knob.
• With a thin screwdriver, adjust the by-pass screw  (see

Fig. 8). If changing from natural gas 20 mbar to liquid
gas, completely tighten the adjustment screw  until a
small regular flame is obtained. If changing from liquid
gas to natural gas 20 mbar, undo the by-pass screw
about 1/2 of a turn. If changing from natural gas 20 mbar
to natural gas 13 mbar undo the by-pass screw  about
1/4 of a turn. If changing from liquid gas to natural gas
13 mbar, undo the by-pass screw about 3/4 of a turn.

• Finally check the flame does not go out when quickly

turning the knob from the maximum position to the
minimum position.

This procedure can easily be carried out, anyhow the hob
has been positioned or built in the working top.

  

Burner

Ø By-pass

in 1/100

of mm

  Auxiliary

28

  Semi-rapid

32

  Rapid

40

  Ultra rapid

56

Table: By-pass diameters

Table: Injectors

Fig. 8

By-pass screw

TYPE

TYPE OF

INJECTORS

NOMINAL

REDUCED

NOMINAL

NOMINAL

OF GAS

BURNER

MARKS

POWER

POWER

POWER

PRESSURE

1/100 mm

INPUT

k W

mbar

k W

m3/h

g/h

Ultra-rapid (triple crown)

146

4,00

1,20

0,381

-

Rapid (large)

113

2,80

0,65

0,267

-

Semi-rapid (medium)

96

2,00

0,45

0,190

-

20

Auxiliary (small)

70

1,00

0,33

0,095

-

Ultra-rapid (triple crown)

98

4,00

1,20

-

288

Rapid (large)

86

2,80

0,65

-

202

Semi-rapid (medium)

71

2,00

0,45

-

144

28-30/37

Auxiliary (small)

50

1,00

0,33

-

72

Ultra-rapid (triple crown)

147

3,00

1,20

0,318

-

Rapid (large)

108

2,13

0,52

0,210

-

Semi-rapid (medium)

105

1,72

0,42

0,186

-

13*

Auxiliary (small)

80

0,90

0,30

0,085

-

NATURAL

GAS
G 20

LPG

(Buthane/

Propane)

Adaptation to different types of gas

!

!

!

!

!

!

!

!

!

!

NATURAL

GAS
G 20

for Russia only.

Содержание EHG 7762












Отзывы: