3
Safety
instructions
Safety instructions
Do not use gas other than that which is specified on the
label attached.
Do not place anything, e.g. flame tamer, asbestos mat,
between pan and pan support as serious damage to the
appliance may result. (Fig 1)
WARNING:
WARNING:
WARNING:
WARNING:----
•
•
•
• In the event of the burner flames being accidentally
In the event of the burner flames being accidentally
In the event of the burner flames being accidentally
In the event of the burner flames being accidentally
extinguished, turn off the burner control knob and do not
extinguished, turn off the burner control knob and do not
extinguished, turn off the burner control knob and do not
extinguished, turn off the burner control knob and do not
attempt to re
attempt to re
attempt to re
attempt to re----ignite the burner for at least 1 minute.
ignite the burner for at least 1 minute.
ignite the burner for at least 1 minute.
ignite the burner for at least 1 minute.
Do not remove the pan support and enclose the burner with a
wok stand not supplied by Electrolux as this will concentrate
the flame and deflect the heat onto the top plate. (Fig 2)
Do not use large pots or heavy weights which can bend the pan
support or deflect the flame onto the top plate.
(Fig 3)
Locate pan centrally over burner so that it is stable and does
not overheat the appliance. (Fig 4)
Use only wok support supplied or recommended by the
manufacturer of the appliance. (Fig 5)
Wok support to be used for wok and other trivets for flat bottom
pot.
The unit to be used for cooking only. Do not dry towels, clothes,
etc., over it. If this is done, there is danger of fire.
If a gas leak is found, close stopcock, open up all windows and
call your dealer. Do refrain from turning an electric switch on or
off, lighting a match, smoking or using a lighter.
Use the appliance in a well-ventilated room.
Do not use vinyl gas hose. It is liable to be softened by heat.
Use only a rubber hose.
Be sure to turn off the ignition knob and regulator of the
cylinder after use.
Avoid touching the burner, pan stand etc., immediately after
use. Otherwise you will get burnt.
Ensure that the rubber hose does not touch any part of the unit
or lies underneath it.
Connect the rubber hose to the gas inlet and fasten it with a
hose clamp.
The pan stand leg nearest to the flame will have discoloration
after use. Such phenomenon is normal.
•
For burner fitted with a flame supervision device, if after 15
For burner fitted with a flame supervision device, if after 15
For burner fitted with a flame supervision device, if after 15
For burner fitted with a flame supervision device, if after 15
sssseconds of ignition operation the burner has not lit, stop
econds of ignition operation the burner has not lit, stop
econds of ignition operation the burner has not lit, stop
econds of ignition operation the burner has not lit, stop
operating the device and open the compartment door and
operating the device and open the compartment door and
operating the device and open the compartment door and
operating the device and open the compartment door and
wait at least 1 minute before attempting a further ignition of
wait at least 1 minute before attempting a further ignition of
wait at least 1 minute before attempting a further ignition of
wait at least 1 minute before attempting a further ignition of
the burner.
the burner.
the burner.
the burner.
•
If nozzle holes are blocked, use a thin wire or pin to pierce
If nozzle holes are blocked, use a thin wire or pin to pierce
If nozzle holes are blocked, use a thin wire or pin to pierce
If nozzle holes are blocked, use a thin wire or pin to pierce
and clean the nozzle holes.
and clean the nozzle holes.
and clean the nozzle holes.
and clean the nozzle holes.
•
Содержание EGT7828CK
Страница 4: ...Parts identification 4 ...
