![Electrolux EFP/W-1100ULS EEC Скачать руководство пользователя страница 6](http://html.mh-extra.com/html/electrolux/efp-w-1100uls-eec/efp-w-1100uls-eec_user-manual_22005006.webp)
6
http://www.home-comfort.com
Maintenance
WARNING:
Before any maintenance and/or cleaning the
exterior of the heater, disconnect the heater
form the power supply and leave heater
cooled off.
• The heater uses an electronically controlled
LED system to create the flame effect
therefore no parts need to be replaced.
Safety cut-out
• This heater is fitted with a safety cut-out
which will operate if the heater overheats
(e.g. Due to blocked air vents). For safety
reasons, the heater will NOT automatically
reset.
• To reset the heater, disconnect the heater
from the mains supply for at least 15 minutes.
Reconnect the supply to the mains and
switch on the heater
Installation instructions
• Do not connect the appliance until
properly fixed to the wall and the
instructions is read fully.
• The minimum distances must be observed.
• For installation of the appliance, care must
be taken not to damage concealed cables.
• Please be careful while drilling the holes.
• This appliance is designed to be
permanently fixed to a wall at a minimum
height of 300 mm.
• The wall bracket must be fitted horizontally
and the cable routed to the bottom right of
the heater.
• A height of 600 mm from bottom of heater
to floor is recommended for optimum
viewing of fuel bed.
• Keep top of heater at least 1000 mm away
from ceiling or other objects for optimum
heat ventilation.
• For optimum viewing, mark the top
four screws fixing positions on wall in
accordance with the recommend fixing
dimensions.
• Drill holes with a six drill bit.
• Fix the wall bracket using that the plug and
screws provided.
• Carefully lift the heater up ensuring that the
top rear ledge of heater engages the wall
bracket and is sitting centrally.
• Lift softly towards the wall.
• Mark the bottom holes position, remove
the heater ensuring that the bottom fixing
Preparation for operation
Decorative fuel (stones) is located on the
side of the polystyrene foam packaging,
on the same side there is a remote control.
Decorative fuel (firewood) (except for EFP/W -
2000S EEC) is in the package behind the front
panel of the device.
Before using:
1. Remove the front panel of the instrument
(except for EFP/W - 2000S EEC).
2. Remove the decorative fuel (firewood),
unpack, install the desired type of
decorative fuel (stones or firewood).
3. Return the front panel to its original
position as shown in the diagram.
4. For model EFP/W - 2000S EEC: Place
stones in an open area in front of the inner
fireplace shield.
Front
panel
Fireplace
body
Fireplace
body
Stones or firewood
Front
panel
Fireplace
body
1.
2.
3.
Содержание EFP/W-1100ULS EEC
